Abstract:In this paper, we proposed a roadmap of the need for silver reduction in industrial silicon solar cells in the TW era. Several metallization approaches towards an intermediate and long‐term target level of 5 mg/W and 2 mg/W have been systematically discussed. Secondly, we presented a promising hybrid metallization design by combining the advantages of screen‐printing and plating technologies to significantly reduce silver consumption thereby achieving the target value of 5 mg/W for TOPCon and 2 mg/W for PERC solar cells. As PV manufacturing heads towards the multi‐TW scale, it is required to carefully evaluate a wide range of concepts including not only efficiency and cost but also material consumption to ensure sustainable manufacturing of PV technologies. The rapid growth of PV could significantly increase the demand for several materials required in solar cells such as silver, aluminium, copper and even silicon, thereby causing dramatic price fluctuations. Furthermore, the PV manufacturing capacity would be at risk of being limited by the supply of some scarce metals, e.g. with current industrial implementations – screen printing (SP) metallization, the capacities of PERC and TOPCon could be capped at 377 GW and 227 GW with 20% of global silver supply available to the PV industry. In addition, PV systems have ~25–30 years lifespan to ensure low LCOE and emissions. Recycling alone will not provide an immediate solution to overcome the limitation of material consumption in the exponentially growing PV market. It is expected that the Ag usage needs to be reduced to no more than 5 mg/W or even 2 mg/W for all solar cell technologies to allow a multi‐TW manufacturing scale without depleting the global silver supply. Therefore, further advancements in metallization technologies are critically and urgently required to significantly reduce the silver consumption of current screen‐printed contacts in industrial silicon solar cells. This paper firstly presents a roadmap towards the 5 mg/W and 2 mg/W silver consumption targets with various metallization technologies and screen‐printing designs. Subsequently, a hybrid plating on screen‐printed metallization design was proposed to improve the performance and reduce the silver consumption of screen‐printed contacts. The experimental results have demonstrated up to 1.08%abs improvements in fill factor and 0.3%abs gains in cell efficiency. In addition, up to 40%rel reductions in finger silver consumption have been achieved without any sacrifices in the electrical conductivity of such hybrid screen‐printed and plated fingers. This work proposes not only a roadmap but also a promising approach to significantly reduce the Ag demand and benefit sustainable production of industrial screen‐printed silicon solar cells in the TW era.

A Horizontal Double‐Sided Copper Metallization Technology Designed for Solar Cell Mass‐Production

Copper metallization of electrodes for silicon heterojunction solar cells: Process, reliability and challenges

Mass production of crystalline silicon solar cells with polysilicon‐based passivating contacts: An industrial perspective

Progress of plated metallization for industrial bifacial TOPCon silicon solar cells

24.18% efficiency TOPCon solar cells enabled by super hydrophilic carbon-doped polysilicon films combined with plated metal fingers

Fabrication and Detailed Analysis of 22.0% Rear Junction Double-side TOPCon Solar Cell with Front SiOx/Polysilicon Selective Emitter

Process challenges of high-performance silicon heterojunction solar cells with copper electrodes

Laser Ablation and Ni/Cu Plating Approach for Tunnel Oxide Passivated Contacts Solar Cells with Variate Polysilicon Layer Thickness: Gains and Possibilities in Comparison to Screen Printing

Low‐cost metallization based on Ag/Cu fingers for exceeding 25% efficiency in industrial silicon heterojunction solar cells

27.6% Perovskite/c‐Si Tandem Solar Cells Using Industrial Fabricated TOPCon Device

Mass production of industrial tunnel oxide passivated contacts (i‐TOPCon) silicon solar cells with average efficiency over 23% and modules over 345 W

Review on Metallization Approaches for High-Efficiency Silicon Heterojunction Solar Cells

Advancing nickel seed layer electroplating for enhanced contact and passivation performance in TOPCon solar cells

Reduce on the Cost of Photovoltaic Power Generation for Polycrystalline Silicon Solar Cells by Double Printing of Ag/Cu Front Contact Layer

Direct Contact Electroplating Sequence Without Initial Seed Layer for Bifacial TOPCon Solar Cell Metallization

Silicon heterojunction back contact solar cells by laser patterning

Enhancing the reliability of TOPCon technology by laser-enhanced contact firing

Novel Tandem Passivated Contact Approach for High-Efficiency Industrial TOPCon Solar Cells

High-efficiency N-Topcon Cells Ensured by an Emitter Preparation Process Without Post-Oxidation

Silver‐lean metallization and hybrid contacts via plating on screen‐printed metal for silicon solar cells manufacturing