Abstract:We report an industrial compatible tunnel oxide passivated contact (TOPCon) structure on solar-grade p-type c-Si wafer as the rear emitter for high-efficiency solar cells, where the ultrathin silicon oxide (SiOx) is made by plasma-assisted oxidation and the P-doped n-type poly-Si (n+-poly-Si) contact layer by plasma-enhanced chemical vapor deposition (PECVD) of hydrogenated amorphous silicon (a-Si:H) with in-situ doping with PH3 and following the high-temperature annealing. The fabrication processes of SiOx and n+-poly-Si layers are systematically optimized. It is found that the optimized annealing temperature for the crystallization and dopant activation is in the range of 850 °C and 880 °C, which is higher than the similar structure with chemically oxidized SiOx (820 °C). In addition, the samples made with higher PH3/SiH4 doping ratio during the a-Si:H deposition need a lower annealing temperature to reach the similar dopant distribution within the samples made with lower doping ratio but annealed at higher temperature, it means that the optimized annealing temperature decreases with the increase of the PH3/SiH4 doping ratio during the deposition of a-Si:H precursor. The optimized process with post-hydrogenation yields excellent surface passivation on the p-type Si substrate with the implied open-circuit voltage (iVoc) of ∼742 mV, the single-side saturated recombination current density (J0) of ∼3.0 fA/cm2, the contact resistivity (ρc) of ∼2–4 mΩ cm2, and the effective minority carrier lifetime (τeff) of ∼1050 μs (Δn = 1 × 1015 cm-3). With these passivation parameters, a simulation study demonstrates the advantage of rear emitter over the conventional front emitter TOPCon solar cell with ∼22.8% achievable efficiency on solar-grade p-type wafers with current industrial constraints, and ∼24.9% on high quality p-type c-Si wafers with the optimized conditions in R&D laboratories. Our study suggests that the p-type c-Si solar cell with a rear n+-poly-Si TOPCon emitter is a viable structure for high-efficiency solar cell production.

Combined Fabrication and Performance Evaluation of TOPCon Back‐Contact Solar Cells with Lateral Power Metal‐Oxide‐Semiconductor Field‐Effect Transistors on a Single Substrate

Combined fabrication and performance evaluation of TOPCon back‐contact solar cells with lateral power MOSFETs on a single substrate

Fabrication and Detailed Analysis of 22.0% Rear Junction Double-side TOPCon Solar Cell with Front SiOx/Polysilicon Selective Emitter

Selective tunnel oxide passivated contact on the emitter of large-size n-type TOPCon bifacial solar cells

Theoretical exploration towards high-efficiency tunnel oxide passivated carrier-selective contacts (TOPCon) solar cells

27.6% Perovskite/c‐Si Tandem Solar Cells Using Industrial Fabricated TOPCon Device

Highly passivated TOPCon bottom cells for perovskite/silicon tandem solar cells

Balancing Charge‐Carrier Transport and Recombination for Perovskite/TOPCon Tandem Solar Cells with Double‐Textured Structures

Performance of Large Area n-TOPCon Solar Cells with Selective Poly-Si Based Passivating Contacts Prepared by PECVD Method

A Horizontal Double‐Sided Copper Metallization Technology Designed for Solar Cell Mass‐Production

An industrially viable TOPCon structure with both ultra-thin SiOx and n+-poly-Si processed by PECVD for p-type c-Si solar cells

Mass production of crystalline silicon solar cells with polysilicon‐based passivating contacts: An industrial perspective

Laser Ablation and Ni/Cu Plating Approach for Tunnel Oxide Passivated Contacts Solar Cells with Variate Polysilicon Layer Thickness: Gains and Possibilities in Comparison to Screen Printing

Advancing Monolithic Perovskite/TOPCon Tandem Solar Cells by Customizing Industrial‐Level Micro‐Nano Structures

Numerical Simulation and Experiment of a High-Efficiency Tunnel Oxide Passivated Contact (TOPCon) Solar Cell Using a Crystalline Nanostructured Silicon-Based Layer

Process development and integration of double-side Poly-Si passivated solar cells with printed contacts via LPCVD and ex-situ tube diffusion

Bathocuproine:Ag Complex Functionalized Tunneling Junction for Efficient Monolithic Perovskite/TOPCon Silicon Tandem Solar Cell

Monolithic Perovskite/Silicon Tandem Solar Cells Fabricated Using Industrial p‐Type Polycrystalline Silicon on Oxide/Passivated Emitter and Rear Cell Silicon Bottom Cell Technology

Mass production of industrial tunnel oxide passivated contacts (i‐TOPCon) silicon solar cells with average efficiency over 23% and modules over 345 W