Abstract:In thermoelectric materials, phase boundaries are crucial for carrier/phonon transport. Manipulation of carrier and phonon scatterings by introducing continuous interface modification has been shown to improve thermoelectric performance. In this paper, a strategy of interface modification based on powder atomic layer deposition (PALD) is introduced to accurately control and modify the phase boundary of pure bismuth. Ultrathin layers of Al2O3, TiO2, and ZnO are deposited on Bi powder by typically 1–20 cycles. All of the oxide layers significantly alter the microstructure and suppressed grain growth. These hierarchical interface modifications aid in the formation of an energy barrier by the oxide layer, resulting in a substantial increase in the Seebeck coefficient that is superior to that of most pure polycrystalline metals. Conversely, taking advantage of the strong electron and phonon scattering, an exceptionally large decrease in thermal conductivity is obtained. A maximum figure of merit, zT, of 0.15 at 393 K and an average zT of 0.14 at 300–453 K were achieved in 5 cycles of Al2O3‐coated Bi. The ALD‐based approach, as a practical interfacial modification technique, can be easily applied to other thermoelectric materials, which can contribute to the development of high‐performance thermoelectric materials of great significance. A surface/interface modification technology based on atomic layer deposition concept is introduced to precisely tune the phase boundary composition of pure bismuth with ultrathin layers of Al2O3, TiO2, and ZnO oxides. Using the strong electron and phonon scattering, a maximum figure of merit (zT) of 0.15 at 393 K was attained for modified Bi with 5 cycles ALD of Al2O3.

Improved contact performance and thermal stability of Co–Ni alloy barrier layer for bismuth telluride-based thermoelectric devices

Ni barrier in Bi2Te3-based thermoelectric modules for reduced contact resistance and enhanced power generation properties

Enhanced Contact Performance and Thermal Tolerance of Ni/Bi2Te3 Joints for Bi2Te3-Based Thermoelectric Devices

Fabrication and Excellent Performances of Bismuth Telluride-Based Thermoelectric Devices.

Enhanced Interfacial Adhesion and Thermal Stability in Bismuth Telluride/Nickel/Copper Multilayer Films with Low Electrical Contact Resistance

Extremely Low Contact Resistivity of Bi 2 Te 3 -Based Modules Enabled by NiP-Based Alloy Barrier

Study on the Preparation and Properties of a Co-Based Barrier Layer by Diffusion Welding

Effect of NiMo Diffusion Barrier Plating Preparation on Microstructure and Properties of Bi2Te3/Cu Joints

Screening metal diffusion barriers for thermoelectric Bi0.5Sb1.5Te3

Enhancing power generation sustainability of thermoelectric pillars by suppressing diffusion at Bi-Sb-Te/Sn electrode interface using crystalline Co-P coatings

Co/Bi2te3 Interfacial Reactions and Bi-Co-Te Phase Equilibria

Effect of Powder ALD Interface Modification on the Thermoelectric Performance of Bismuth

Enhanced Thermoelectric and Mechanical Properties of p-type Bi0.5Sb1.5Te3 Bulk Alloys by Composite Electroless Plating with Ni&Cu

Interfacial Stability in Bi2Te3 Thermoelectric Joints

Highly Effective GeNi Alloy Contact Diffusion Barrier for BiSbTe Long-Term Thermal Exposure

Ni–W–P layer-induced strength improvement of solder joint in Bi2Te3 thermoelectric module

Precision Interface Engineering of an Atomic Layer in Bulk Bi2Te3 Alloys for High Thermoelectric Performance

Enhanced thermoelectric properties of layered anisotropic PbBi2Te4 through the suppression of bipolar diffusion effect via Se alloying

Bonding/barrier layers on bismuth telluride (Bi2Te3) for high temperature applications

Electroless nickel deposition over the surface of bismuth telluride wafer as a barrier layer

BiSbTe alloy with high thermoelectric and mechanical performance for power generation