Abstract:Multi-phase compatibilizers are potentially attractive, not only for the preparation of ternary or multi-phase immiscible polymer blends with high performance, but also for recycling and reuse of waste plastics mixture. In this study, the maleic anhydride (MAH) and styrene (St) dual monomers grafted PP, PP-g-(MAH-co-St) is prepared as a multi-phase compatibilizer, which exhibits highly effective compatibility on the PP/PA6/SEBS (70/15/15) ternary blends. Scanning electron microscopy (SEM) reveals that, with increasing the compatibilizer, the morphology evolves from the individual PA6 particle encapsulated by SEBS to several smaller-size PA6 particles partially encapsulated by SEBS phase, then to the tiny PA6 particles and some larger-size SEBS agglomerates predominantly dispersed separately in PP matrix. The morphology development predicted by spreading coefficients shows a consummate consistency with that observed by SEM. Moreover, the good compatibilization and corresponding morphologies result in superior enhancement of mechanical properties. Compared to the uncompatibilized blend, adding 15 wt multi-phase compatibilizer to the blend leads to the best mechanical properties with the yield stress, stress at break, strain at break and impact failure energy improved significantly by 23%, 132%, 647% and 220%, respectively. The results verify that the domains with small-size PA6 particles (03-0.4 mu m) partially encapsulated by SEBS (0.5-0.7 mu m) in PP matrix are very effective to enhance the mechanical properties of the blends. The morphologies of large-size PA6 particles encapsulated by SEBS or tiny PA6 particles and some larger-size SEBS agglomerates dispersed separately in PP matrix for the enhancement in mechanical properties of the blends are very limited. Consequently, the enhanced interfacial interactions and the morphology with the rigid particles partially encapsulated by a rubber-like phase in matrix are crucial for the ternary polymer.blends. (C) 2016 Elsevier Ltd. All rights reserved.

Synergistic compatibilization effect on phase morphology evolution and properties of poly(ether- block -amide)/ethylene-vinyl acetate blends

Synergetic Effect of a Reactive Compatibilizer and Organo-montmorillonite on the Dispersion of Polyamide 6 /Polydimethylsilicone Blend with a High Viscosity Ratio

Structure-property Relationships of Reactively Compatibilized PHB/EVA/starch Blends.

Well-Defined Pe-B-Pdms Diblock Copolymers Via The Combination Of Thiol-Ene Click And Esterification Reactions: Facile Synthesis And Compatibilization For Hdpe/Silicone Oil Blends

Effect Of Polyethersulfone On The Mechanical And Rheological Properties Of Polyetherimide-Modified Epoxy Systems

Viscoelastic Effects on the Phase Separation in Thermoplastics-Modified Epoxy Resin

Morphology Development and Superior Mechanical Properties of Pp/Pa6/Sebs Ternary Blends Compatibilized by Using A Highly Efficient Multi-Phase Compatibilizer

Correlation of Morphology Evolution with Superior Mechanical Properties in PA6/PS/PP/SEBS Blends Compatibilized by Multi-phase Compatibilizers

EVA and SEBS-MA copolymers incorporated silicone rubber/SEBS blends: improvement of mechanical and thermal properties

Super Tough PA6/PP/ABS/SEBS Blends Compatibilized by a Combination of Multi-Phase Compatibilizers

Blends of rABS and SEBS: Influence of In-Situ Compatibilization on the Mechanical Properties

Compatibilizing modification of polyethersulfone/polycarbonate blend

Morphological, Thermal, and Mechanical Characterization of Bio-Based High-Density Polyethylene / Biopolyamide 6.10 Blends Compatibilized with PE and SEBS Functionalized With Maleic Anhydride

Compatibilization and morphology development of immiscible ternary polymer blends

Morphology, rheology, and mechanical properties of polylactide/ poly(ethylene-co-octene) blends

Effect of compatibilizer and polyhedral oligomeric silsesquioxane on mechanical, thermal, and morphological properties of polyamide6/poly (ethylene-co-vinyl acetate) composites

Creating Super-Tough and Strong PA6/ABS Blends Using Multi-Phase Compatibilizers

Studies on blends of LLDPE and polar polymers compatibilized by a random copolymer

Effect of Different Compatibilizers on the Properties of Poly (Lactic Acid)/Poly (Butylene Adipate-Co-Terephthalate) Blends Prepared under Intense Shear Flow Field

Reactive Compatibilization of Polyamide 6/Olefin Block Copolymer Blends: Phase Morphology, Rheological Behavior, Thermal Behavior, and Mechanical Properties

Study of polypropylene/polyethylene terephthalate blends compatibilized with polypropylene double‐grafted maleic anhydride and epoxy resin