Abstract:Multi-phase compatibilizers are potentially attractive, not only for the preparation of ternary or multi-phase immiscible polymer blends with high performance, but also for recycling and reuse of waste plastics mixture. In this study, the maleic anhydride (MAH) and styrene (St) dual monomers grafted PP, PP-g-(MAH-co-St) is prepared as a multi-phase compatibilizer, which exhibits highly effective compatibility on the PP/PA6/SEBS (70/15/15) ternary blends. Scanning electron microscopy (SEM) reveals that, with increasing the compatibilizer, the morphology evolves from the individual PA6 particle encapsulated by SEBS to several smaller-size PA6 particles partially encapsulated by SEBS phase, then to the tiny PA6 particles and some larger-size SEBS agglomerates predominantly dispersed separately in PP matrix. The morphology development predicted by spreading coefficients shows a consummate consistency with that observed by SEM. Moreover, the good compatibilization and corresponding morphologies result in superior enhancement of mechanical properties. Compared to the uncompatibilized blend, adding 15 wt multi-phase compatibilizer to the blend leads to the best mechanical properties with the yield stress, stress at break, strain at break and impact failure energy improved significantly by 23%, 132%, 647% and 220%, respectively. The results verify that the domains with small-size PA6 particles (03-0.4 mu m) partially encapsulated by SEBS (0.5-0.7 mu m) in PP matrix are very effective to enhance the mechanical properties of the blends. The morphologies of large-size PA6 particles encapsulated by SEBS or tiny PA6 particles and some larger-size SEBS agglomerates dispersed separately in PP matrix for the enhancement in mechanical properties of the blends are very limited. Consequently, the enhanced interfacial interactions and the morphology with the rigid particles partially encapsulated by a rubber-like phase in matrix are crucial for the ternary polymer.blends. (C) 2016 Elsevier Ltd. All rights reserved.

Morphological, Thermal, and Mechanical Characterization of Bio-Based High-Density Polyethylene / Biopolyamide 6.10 Blends Compatibilized with PE and SEBS Functionalized With Maleic Anhydride

Well-Defined Pe-B-Pdms Diblock Copolymers Via The Combination Of Thiol-Ene Click And Esterification Reactions: Facile Synthesis And Compatibilization For Hdpe/Silicone Oil Blends

MORPHOLOGICAL EVOLUTION AND VISCOELASTIC BEHAVIOR OF COMPATIBILIZED HDPE/PA6 BLENDS

Reactive Compatibilization of Polyamide 6/Olefin Block Copolymer Blends: Phase Morphology, Rheological Behavior, Thermal Behavior, and Mechanical Properties

Compatibilization of LDPE/PA6 by Using a LDPE Functionalized with a Maleinized Hyperbranched Polyester Polyol

Detailed comparison of compatibilizers MAPE and SEBS-g-MA on the mechanical/thermal properties, and morphology in ternary blend of recycled PET/HDPE/MAPE and recycled PET/HDPE/SEBS-g-MA

Study on the Microstructures and Mechanical Behaviour of Compatibilized Polypropylene/Polyamide-6 Blends

Synergistic compatibilization effect on phase morphology evolution and properties of poly(ether- block -amide)/ethylene-vinyl acetate blends

Blending of Low-Density Polyethylene and Poly(Butylene Succinate) (LDPE/PBS) with Polyethylene–Graft–Maleic Anhydride (PE–g–MA) as a Compatibilizer on the Phase Morphology, Mechanical and Thermal Properties

Effect of compatibilizer and polyhedral oligomeric silsesquioxane on mechanical, thermal, and morphological properties of polyamide6/poly (ethylene-co-vinyl acetate) composites

Morphology, rheology, and mechanical properties of polylactide/ poly(ethylene-co-octene) blends

Polyethylene/maleic Anhydride Grafted Polyethylene/organic‐montmorillonite Nanocomposites. I. Preparation, Microstructure, and Mechanical Properties

Rheology of Poly(lactic Acid)/poly(trimethylene Terephthalate) Blends Compatibilized by Clay or Maleic Anhydride-Grafted Poly(ethylene-Octene) Elastomer

Synergetic Effect of a Reactive Compatibilizer and Organo-montmorillonite on the Dispersion of Polyamide 6 /Polydimethylsilicone Blend with a High Viscosity Ratio

From Waste Vegetable Oil to a Green Compatibilizer for HDPE/PA6 Blends

Performance Enhancement of Biopolyester Blends by Reactive Compatibilization with Maleic Anhydride-Grafted Poly(butylene succinate-co-adipate)

Morphology Development and Superior Mechanical Properties of Pp/Pa6/Sebs Ternary Blends Compatibilized by Using A Highly Efficient Multi-Phase Compatibilizer

Study of Compatibility Between Laminar Structure and Barrier Properties of Polyethylene/Modified Polyamide Blends

Compatibilization Effect of PP-g-(MAH/VAc) on Polypropylene/Polyamide 6 Blends

Effect of poly(styrene-co-maleic anhydride) on physical properties and crystalline behavior of nylon-6/PEBA blends

Study of polypropylene/polyethylene terephthalate blends compatibilized with polypropylene double‐grafted maleic anhydride and epoxy resin