Abstract:This study aims to examine the 50/50 polypropylene/polyamide 6 (iPP/PA6) system molded under confined flow conditions, both in its original state and after being modified by two different interfacial agents. This study provides two main insights. Firstly, it focuses on a polymer blend close to phase inversion. Secondly, it investigates the impact of using two different types of interfacial agents (derived from polymer waste) to enhance the compatibility between iPP and PA6. Dynamic Mechanical Analysis (DMA) has been employed to achieve these objectives. It is important to note that the investigation of the 50/50 iPP/PA6 system is a crucial focus predicted in previous studies, where a series of mechanical properties were evaluated using Box–Wilson design of experiments (DOEs) over the whole compositional range on the iPP/PA6 binary system. Thus, two interfacial modifiers, namely succinic anhydride (SA)-grafted atactic polypropylene with terminal, side, and bridge SA grafts (aPP-SASA) and succinyl-fluoresceine (SF) with bridge succinic anhydride grafting atactic polypropylene (aPP-SFSA), were employed. The authors obtained and characterized these agents. The quantity of these agents used in the blend was identified as a critical coordinate in prior studies conducted by the authors. The processing method used, compression molding under confined conditions, was chosen to minimize any orientation effect on the emerging morphology. All characterization procedures were performed on samples processed by contour machining to retain the blend morphologies as they emerged from the processing stage. Results from WAXS and SAXS synchrotron tests concluded there were no changes in the crystal morphology of the iPP or the PA6 in the blends nor any co-crystallization process throughout the compositional range. These findings, and the long period fits on the PP crystalline phase for the fifty/fifty blends we are discussing, will support the present DMA study. Finally, the efficiency of these interfacial modifiers has been concluded, even in this unfavorable scenario.

MORPHOLOGICAL EVOLUTION AND VISCOELASTIC BEHAVIOR OF COMPATIBILIZED HDPE/PA6 BLENDS

A Dissipative Particle Dynamics Study on the Compatibilizing Process of Immiscible Polymer Blends with Graft Copolymers

Synergetic Effect of a Reactive Compatibilizer and Organo-montmorillonite on the Dispersion of Polyamide 6 /Polydimethylsilicone Blend with a High Viscosity Ratio

Rheological Properties of PET/PA66/Liquid Crystalline Copolyesteramide Blends

Synthesis, characterization and lubricating effect of long chain branched polydimethylsiloxane-g-polyethylene copolymers

Melt Rheological and Thermoresponsive Shape Memory Properties of HDPE/PA6/POE-g-MAH Blends

Morphology, rheology, and mechanical properties of polylactide/ poly(ethylene-co-octene) blends

Reactive Compatibilization of Polyamide 6/Olefin Block Copolymer Blends: Phase Morphology, Rheological Behavior, Thermal Behavior, and Mechanical Properties

Morphological, Thermal, and Mechanical Characterization of Bio-Based High-Density Polyethylene / Biopolyamide 6.10 Blends Compatibilized with PE and SEBS Functionalized With Maleic Anhydride

Dynamic Rheological Behavior of Hdpe/Uhmwpe Blends

Rheology of Poly(lactic Acid)/poly(trimethylene Terephthalate) Blends Compatibilized by Clay or Maleic Anhydride-Grafted Poly(ethylene-Octene) Elastomer

A Dynamic Mechanical Analysis on the Compatibilization Effect of Two Different Polymer Waste-Based Compatibilizers in the Fifty/Fifty Polypropylene/Polyamide 6 Blend

Compatibilization Effect of MMA-co-GMA Copolymers on the Properties of Polyamide 6/poly(vinylidene Fluoride) Blends

Rheological Behavior and Mechanical Properties of High‐density Polyethylene Blends with Different Molecular Weights

Compatibilization Effect of PP-g-(MAH/VAc) on Polypropylene/Polyamide 6 Blends

Study on the Microstructures and Mechanical Behaviour of Compatibilized Polypropylene/Polyamide-6 Blends

Compatibility evaluation and mechanical properties of isotactic polypropylene/high density polyethylene (iPP/HDPE) blends

Friction and Wear Mechanisms of Polyamide 66/high Density Polyethylene Blends

Morphology and Mechanical Properties of Nylon 6/PBT Blends Compatibilized with Styrene/Maleic Anhydride Copolymer

Morphology Development and Superior Mechanical Properties of Pp/Pa6/Sebs Ternary Blends Compatibilized by Using A Highly Efficient Multi-Phase Compatibilizer

Compatibilization of LDPE/PA6 by Using a LDPE Functionalized with a Maleinized Hyperbranched Polyester Polyol