Abstract:In order to improve the wear and corrosion resistance of Ti-6Al-4V, a novel beta-Ta2O5 nanoceramic coating was synthesised using reactive sputter deposition enabled by double glow discharge plasma technique. The surface topography, chemical composition, and microstructure of the newly developed coating were characterised by a variety of surface analytical techniques. The coating microstructure was found to exhibit a compact striated pattern extending in a direction perpendicular to coating surface, which is composed of equiaxed beta-Ta2O5 grains with an average grain size of similar to 20 nm, well adhered to the Ti-6A1-4V substrate. The hardness and the Young's modulus of the as-deposited coating were obtained by nanoindentation, and the adhesion strength between the coating and substrate was determined by a scratch tester. The dry sliding wear behaviours of the coating were investigated at room temperature against Si3N4 ceramic balls at room temperature under applied loads ranging from 2.3 N to 5.3 N using a ball-on-disc tribometer. The specific wear rates of the coating exhibited only a slight increase with applied normal load, and were shown to be two orders of magnitude lower than that for Ti-6Al-4V under the same loading condition. Furthermore, the electrochemical behaviour of the coating immersed in 3.5 wt.% NaCl solution was systematically examined by using a range of complementary electrochemical techniques including potentiodynamic polarisation, electrochemical impedance spectroscopy (EIS), MottSchottky analysis as well as potential of zero charge (PZC). The results showed that the corrosion resistance of the beta-Ta2O5 nanoceramic coating was better than that of Ti-6Al-4V alloy in 3.5 wt.% NaCl solution. Hence, by possessing higher mechanical properties and good wear and corrosion resistance, the beta-Ta2O5 nanoceramic coating is considered to be a promising candidate for protection of engineering components operating under harsh conditions. (C) 2016 Elsevier B.V. All rights reserved.

FRICTION AND WEAR PERFORMANCE OF AN ELECTROSPARK-DEPOSITED Ta COATING ON CrNi3MoVA ST

Tribological Properties of Ta‐C‐N and Ta‐N Thin Films

Study on Wear and Friction Resistance of CrTiAlMoN Coatings Deposited by Magnetron Sputtering

Effect of TaC content on microstructure and wear behavior of PRMMC Fe-TaC coating manufactured by electrospark deposition on AISI304 stainless steel

Microstructure and properties of Ta-reinforced NiCuBSi + WC composite coating deposited on 5Cr5MoSiV1 steel substrate by laser cladding

Effect of TiC addition on the microstructure and properties of Ni3Ta–TaC reinforced Ni-based wear-resistant coating

Corrosion and Wear Behaviours of a Reactive-Sputter-deposited Ta2O5 Nanoceramic Coating

Friction and wear performance of electrospark deposited Ni/C-MoS2 self-lubricating coating

The Effect of RF Sputtering Power on Structural, Nanomechanical and Tribological Properties of Single Layered TaN Coatings

Influence of Cr on the Surface Properties of the Micro-Textured WC+Co Alloy Coating

Microstructure and Friction Properties of CoCrFeMnNiTix High-Entropy Alloy Coating by Laser Cladding

Tribological and Corrosion Properties of the CoCrAlYTaSiC-xCNTs Coatings Deposited by Laser Cladding

Wear and corrosion behaviour of nanocrystalline TaN, ZrN, and TaZrN coatings deposited on biomedical grade CoCrMo alloy

Microstructure, Mechanical, and Tribological Properties of Cr-Ti-Si-N Coatings

Microstructure, Wear Behaviour and Laser Ablation Behaviour of Double Glow Plasma Alloyed Ta-W Coating

Investigation into Microstructure, Wear Resistance in Air and NaCl Solution of AlCrCoNiFeCTax High-Entropy Alloy Coatings Fabricated by Laser Cladding

Tribological properties and microstructure of monolayer and multilayer Ta coatings prepared by magnetron sputtering

Friction and Wear Properties of CoCrFeNiMnSnx High Entropy Alloy Coatings Prepared via Laser Cladding

A Comprehensive Investigation on Nanomechanical, Scratch, and Tribological Characteristics of TaN-Ag Nanocomposite Coating on Ti6Al7Nb Alloy

Friction and wear behaviors of TiCN coating based on electrical discharge coating

SEM and SEAM study on tribological performance of cermets coatings