Abstract:Perovskite solar cells (PSCs) have shown high optical absorption and consequently provide high conversion efficiency with stable performance. In our work, CH 3 NH 3 PbI 3 (MAPbI 3 ) as an absorber layer is analyzed for different crystalline structures. Cubic, tetragonal, and orthorhombic phases of perovskite material are investigated to check the impact of the crystalline structure on the solar cell performance. Both density of states and band structure are studied using Quantum-ESPRESSO package depending on density functional theory. Then, all relevant parameters were employed in SCAPS software and comprehensive study was done for examining the effect of the crystalline structure of perovskite layer on the solar cell performance. In-depth, analyses were conducted to evaluate key parameters, including open circuit voltage (V oc ), short circuit current (I sc ), fill factor (FF), and power conversion efficiency (PCE) considering the variations of perovskite layer thickness and bulk defect densities. The obtained results indicate that cells with cubic MAPbI 3 , which shows a notably higher bandgap of 1.7 eV and an enhanced optical absorption coefficient, especially in the higher wavelength range (around 10 5 cm −1 ), show better performance for almost all three scenarios. Cubic MAPbI 3 cells achieve relatively higher peak efficiency of 26% when the absorber layer thickness is almost 900 nm. The investigation into absorber bulk defect densities reveals the critical role of defect levels in PSC performance. Adjusting defect levels from 10 14 cm −3 to 10 18 cm −3 results in deteriorating trends in V oc , J sc , FF, and PCE. J sc remains stable until a defect level of 10 17 cm −3 , highlighting a threshold where defects begin to impact charge carrier generation and separation. Doping effect has been studied, PCE remains stable until a critical doping level of 10 16 cm −3 after which it drops significantly which indicates that doping is cautioned against due to its adverse effects on material and carrier transport. This finding holds significant promise for experimental solar cell fabrication, as it suggests that cubic MAPbI 3 's superior bandgap and enhanced optical absorption could lead to more efficient and robust photovoltaic devices in real-world applications.

Wide-bandgap MAPbBr 3 perovskite solar cells using bifunctional-molecule additives achieving a high open-circuit voltage of 1.63 V

Phase Engineering of Perovskite Materials for High-Efficiency Solar Cells: Rapid Conversion of CH3NH3PbI3 to Phase-Pure CH3NH3PbCl3 Via Hydrochloric Acid Vapor Annealing Post-Treatment

An Amorphous Precursor Route To The Conformable Oriented Crystallization Of Ch3nh3pbbr3 In Mesoporous Scaffolds: Toward Efficient And Thermally Stable Carbon-Based Perovskite Solar Cells

Air-processed MAPbI3 perovskite solar cells achieve 20.87% efficiency and excellent bending resistance enabled via polymer dual-passivation strategy

Comprehensive performance analysis of perovskite solar cells based on different crystalline structures of MAPbI3

Zwitterion Coordination Induced Highly Orientational Order of CH 3 NH 3 PbI 3 Perovskite Film Delivers a High Open Circuit Voltage Exceeding 1.2 V

Precursor engineering for performance enhancement of hole-transport-layer-free carbon-based MAPbBr3 perovskite solar cells

Thermally Stable Mapbi(3) Perovskite Solar Cells with Efficiency of 19.19% and Area over 1 Cm(2) Achieved by Additive Engineering

Suppressing charge recombination in a methylammonium-free wide-bandgap perovskite film for high-performance and stable perovskite solar cells

Multifunctional Thiophene Cascading SnO2/Perovskite Interfaces for Efficient and Stable MAPbI3 Photovoltaics

Coordinating light management and advance metal nitride interlayer enables MAPbI3 solar cells with >21.8% efficiency

Structure engineering of hierarchical layered perovskite interface for efficient and stable wide bandgap photovoltaics

Efficient and stable planar MAPbI3 perovskite solar cells based on a small molecule passivator

Enhanced Efficiency and Stability of Wide‐Bandgap Perovskite Solar Cells Via Molecular Modification with Piperazinium Salt

Constructing 2D passivation layer on perovskites based on 3-chlorobenzylamine enables efficient and stable perovskite solar cells

Tri‐Brominated Perovskite Film Management and Multiple‐Ionic Defect Passivation for Highly Efficient and Stable Solar Cells

Low-Temperature robust MAPbI 3 perovskite solar cells with power conversion efficiency exceeding 22.4%

Benzylamine‐Treated Wide‐Bandgap Perovskite with High Thermal‐Photostability and Photovoltaic Performance

Crystallization and Defect Chemistry Dual Engineering for MAPbI 3 Perovskite Solar Cells with Efficiency Approaching 22%

BT-MA 0.6 FA 0.4 PbI 3– x Cl x Unsymmetrical Perovskite for Solar Cells with Superior Stability and PCE over 23%

Multifunctional Brominated Graphene Oxide Boosted Charge Extraction for High-Efficiency and Stable All-Inorganic CsPbBr3 Perovskite Solar Cells