Abstract:Carbon-based inorganic CsPbX3 (X = I, Br, Cl) perovskite solar cells (PSCs) are attracting great attention in the photovoltaic field because of their low cost, simple process, and superior thermal stability. However, the large difference in energy band between the CsPbX3 and carbon electrode leads to the poor hole extraction and unfavorable charge recombination, thus deteriorating device's efficiency. In this work, a solution-processed dopant-free tin phthalocyanine (SnPc) film is used as a hole-transport layer (HTL) to fabricate carbon-based CsPbI2Br PSCs by a low-temperature process. At the optimal process, the device achieves a maximum efficiency of 11.39% with less hysteresis, which is much higher than 9.22% of reference device without the SnPc HTL. Moreover, the unencapsulated device exhibits the improved stability and remains about 90% of its initial efficiency after 30 days in ambient air (20–25 °C) with 25–35% relative humidity (RH). This finding reveals that the solution-processed dopant-free SnPc HTL can significantly promote charge transport and suppress charge recombination at the CsPbI2Br/carbon interface. This work provides a low-temperature and solution-processed method to fabricate the efficient and stable carbon-based inorganic PSCs.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsaem.0c01184?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsaem.0c01184</a>.Photovoltaic parameters corresponding to Table S1, Table S4, Figure S3, and Figure S9; quantified atomic ratio for the SnPc-film as obtained from EDS measurement; a summary of annealing temperature, Voc, and PCE values measured under RS direction for carbon-based CsPbI2Br PSCs reported in recent years; the values of Jph*, Jph#, Jsat, Jph*/Jsat, Jph#/Jsat, and Gmax; fitting parameters of TRPL decay spectra; fitting values of different electronic parameters obtained from the Nyquist plots; XRD patterns and photo images of PbI2, PbI2(DMSO), PbBr2, and PbBr2(DMSO) powders; thickness of SnPc HTL measured by an ellipsometer; J–V curves of SnPc-PSCs with different SnPc solution concentrations; EDS spectra of the SnPc-film; XRD patterns of SnPc powder and SnPc film annealed at 120 °C; the schematic of energy level diagram; the steady-state current density as a function of time measured at the maximum power output point; spectrum for the thickness of CsPbI2Br layer; two possible growth models while depositing solution-processed dopant-free SnPc on the CsPbI2Br surface; KPFM images and CPD values of SnPc films based on different SnPc solution concentrations (<a class="ext-link" href="/doi/suppl/10.1021/acsaem.0c01184/suppl_file/ae0c01184_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

An Amorphous Precursor Route To The Conformable Oriented Crystallization Of Ch3nh3pbbr3 In Mesoporous Scaffolds: Toward Efficient And Thermally Stable Carbon-Based Perovskite Solar Cells

An amorphous precursor route to the conformable oriented crystallization of CH<sub>3</sub>NH<sub>3</sub>PbBr<sub>3</sub>in mesoporous scaffolds: toward efficient and thermally stable carbon-based perovskite solar cells

Precursor engineering for performance enhancement of hole-transport-layer-free carbon-based MAPbBr3 perovskite solar cells

Phase Engineering of Perovskite Materials for High-Efficiency Solar Cells: Rapid Conversion of CH3NH3PbI3 to Phase-Pure CH3NH3PbCl3 Via Hydrochloric Acid Vapor Annealing Post-Treatment

Wide-bandgap MAPbBr 3 perovskite solar cells using bifunctional-molecule additives achieving a high open-circuit voltage of 1.63 V

Mixed-Bromide Halide Exchange toward Efficient and Stable Carbon-Electrode CsPbBr 3 Solar Cells

High-performance Carbon Electrode-Based CsPbI2Br Inorganic Perovskite Solar Cell Based on Poly(3-Hexylthiophene)-carbon Nanotubes Composite Hole-Transporting Layer.

CsPbBr3 quantum dots assisted crystallization of solution-processed perovskite films with preferential orientation for high performance perovskite solar cells

CH 3 NH 3 PbBr 3– x I x Quantum Dots Enhance Bulk Crystallization and Interface Charge Transfer for Efficient and Stable Perovskite Solar Cells

High-quality CsPbBr3 films prepared by introducing methylammonium iodide into PbBr2 precursor for efficient perovskite solar cells

Highly Crystalline CsPbI2Br Films for Efficient Perovskite Solar Cells Via Compositional Engineering

Tri‐Brominated Perovskite Film Management and Multiple‐Ionic Defect Passivation for Highly Efficient and Stable Solar Cells

Improvement of Cs-(FAPbI(3))(0.85)(MAPbBr(3))(0.15) Quality Via DMSO-Molecule-Control to Increase the Efficiency and Boost the Long-Term Stability of 1cm(2) Sized Planar Perovskite Solar Cells

Tailoring of CsPbIBr2 Perovskite Crystallization Via Phenylthiourea for Stable and Efficiency Perovskite Solar Cells

Enhanced efficiency and long-term stability of all inorganic CsPbBr 3 perovskite solar cells via regulation of charge separation and extraction by band engineered-Co 3 O 4 nanocrystals as a hole transport material layer

Energy Level Tuning in CsPbBr3 Perovskite Solar Cells through In Situ-Polymerized PEDOT Hole Transport Layer

A Solution-Processed Dopant-Free Tin Phthalocyanine (SnPc) Hole Transport Layer for Efficient and Stable Carbon-Based CsPbI 2 Br Planar Perovskite Solar Cells Prepared by a Low-Temperature Process

Strengthened Interficial Adhesive Fracture Energy by Young's Modulus Matching Degree Strategy in Carbon‐Based HTM Free MAPbI3 Perovskite Solar Cell with Enhanced Mechanical Compatibility

Multifunctional Thiophene Cascading SnO2/Perovskite Interfaces for Efficient and Stable MAPbI3 Photovoltaics

Enhanced efficiency and long-term stability of all inorganic CsPbBr3 perovskite solar cells via regulation of charge separation and extraction by band engineered-Co3O4 nanocrystals as a hole transport material layer

Optimizing the Substrate Pre-Heating and Post-Annealing Temperatures for Fabricating High-Performance Carbon-Based CsPbIBr2 Inorganic Perovskite Solar Cells