Abstract:Obtaining a perovskite light-absorbing layer with good crystallization, low defect concentration, good stability, and well-matched energy levels is critical to obtaining high-efficiency perovskite solar cells (PSCs). Here, a hybrid PSC with a graded band gap is explored using MAPbBr3 (MA = CH3NH3) and MAPbBr0.9I2.1 quantum dots (QDs) as component cells. We have creatively designed a solar cell device with a double-QD structure [indium tin oxide (ITO)/SnO2/perovskite:MAPbBr3 QDs/MAPbBr0.9I2.1 QDs/Spiro-OMeTAD/Au]. A better crystal film of the perovskite absorption layer can be obtained because the MAPbBr3 QDs are doped in an antisolvent, which induces nucleation and growth in the polycrystalline perovskite. In addition, we expect that digestive ripening occurred in the crystallization, and the oleic acid ligands on the surface of the QDs disintegrate during the doping process and transfer to the surface of the perovskite absorption layer finally; it follows that the hydrophobicity and stability of the perovskite film are greatly enhanced. Moreover, a thin film of MAPbBr0.9I2.1 QDs is introduced between the perovskite absorption layer and the hole layer, acting as an energy-level ladder, which leads to well-matched energy levels, an increase in fill factor (FF), and an enhanced hole transport capability. In particular, the mechanism of the crystallization process involving the effect of oleic acid ligands on the interior and surface of the perovskite film is fully discussed here. The final research results from the PSCs show that both high efficiency and long-term stability are achieved successfully by this design strategy.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c14191?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c14191</a>.Parameters of carrier lifetimes in TRPL, parameters and calculated values in the Owens two-liquid method experiment, and J–V parameters; QD dispersion images; AFM images; perovskite film images; contact-angle test images; EIS spectrum; and boxplot of J–V parameters (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c14191/suppl_file/am0c14191_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Zwitterion Coordination Induced Highly Orientational Order of CH 3 NH 3 PbI 3 Perovskite Film Delivers a High Open Circuit Voltage Exceeding 1.2 V

Phase Engineering of Perovskite Materials for High-Efficiency Solar Cells: Rapid Conversion of CH3NH3PbI3 to Phase-Pure CH3NH3PbCl3 Via Hydrochloric Acid Vapor Annealing Post-Treatment

Wide-bandgap MAPbBr 3 perovskite solar cells using bifunctional-molecule additives achieving a high open-circuit voltage of 1.63 V

Ligand‐Induced In Situ Epitaxial Growth of PbI2 Nanosheets/MAPbI3 Heterojunction Realizes High‐Performance HTM‐Free Carbon‐Based MAPbI3 Solar Cells

CH 3 NH 3 PbBr 3– x I x Quantum Dots Enhance Bulk Crystallization and Interface Charge Transfer for Efficient and Stable Perovskite Solar Cells

Crystallization and Defect Chemistry Dual Engineering for MAPbI 3 Perovskite Solar Cells with Efficiency Approaching 22%

Coordinating light management and advance metal nitride interlayer enables MAPbI3 solar cells with >21.8% efficiency

Multifunctional Thiophene Cascading SnO2/Perovskite Interfaces for Efficient and Stable MAPbI3 Photovoltaics

A Versatile Molten‐salt Induction Strategy to Achieve Efficient CsPbI3 Perovskite Solar Cells with a High Open‐circuit Voltage >1.2 V

Imidazole-Based Ionic Liquid Engineering for Perovskite Solar Cells with High Efficiency and Excellent Stability

Passivation Mechanism of Perovskite Upper Interface based on MAPbBr3 Quantum Dots for Efficient and Stable Perovskite Solar Cells

Interface Engineering of Imidazolium Ionic Liquids toward Efficient and Stable CsPbBr3 Perovskite Solar Cells

Efficient and stable planar MAPbI3 perovskite solar cells based on a small molecule passivator

Synergistic Effects of Multifunctional Lanthanides Doped CsPbBrCl 2 Quantum Dots for Efficient and Stable MAPbI 3 Perovskite Solar Cells

ZnO/SnO2 Double Electron Transport Layer Guides Improved Open Circuit Voltage for Highly Efficient CH3NH3PbI3-Based Planar Perovskite Solar Cells

Effects of passivated molecular side group on inverted inorganic CsPbI2Br perovskite solar cells

Increasing the wettability and reducing excess PbI2 using diamine hydrobromides with different lengths at the buried interface of the 3D perovskite film

Controlled Orientation of Perovskite Films Through Mixed Cations Toward High Performance Perovskite Solar Cells

Zwitterionic Ionic Liquid Confer Defect Tolerance, High Conductivity, and Hydrophobicity toward Efficient Perovskite Solar Cells Exceeding 22% Efficiency

2D PEA 2 PbI 4 –3D MAPbI 3 Composite Perovskite Interfacial Layer for Highly Efficient and Stable Mixed-Ion Perovskite Solar Cells

Multifunctional Metal‐organic Frameworks Capsules Modulate Reactivity of Lead Iodide toward Efficient Perovskite Solar Cells with Ultraviolet Resistance