Abstract:Silicon carbide(SiC)is an important material for shielding nuclear fission products in tri-structural isotropic(TRISO)particles for high-temperature gas-cooled reactors.It has an important influence on the safety performance of TRISO particles.Therefore,it is necessary to study the irradiation behaviors and mechanical properties of the SiC layer of TRISO particles.The irradiation process and nanoindentation process can be described accurately by molecular dynamics simulations.It is helpful to analyze the irradiation behavior and mechanical properties of materials.In this paper,molecular dynamics simulations were used to study the irradiation behavior of equiaxed polycrys-talline and long-axis polycrystalline SiC layers obtained from experiments.The calculat-ed theoretical values of the irradiation swelling degree and mechanical properties of the SiC layer are in good agreement with the experimental values.It shows the strong appli-cability of the potential functions and other simulation system parameters used in this paper.The irradiation behavior of the SiC layer was studied in detail by swelling degree,density,atomic structure type,and point defect evolution.The results show that the grain structure of the SiC layer has no significant effect on its irradiation swelling and amorphization.The amorphization is not directly converted from the crystal structure to the amorphous structure during the irradiation process.The crystal structure is conver-ted into an intermediate state structure and then converted into an amorphous structure.The point defects are mainly C vacancies,Si interstitial atoms,and C antisite atoms in the early stage of irradiation.The difference between the ratio of C point defects and Si point defects gradually disappears after the irradiation dose tends to be saturated.The evolution of amorphization and point defects tends to start nearby the grain boundaries.Irradiation reduces the mechanical properties of SiC layers.It no longer has a significant effect on the mechanical properties of the SiC layer after the irradiation dose tends to be saturated.The changes in the mechanical properties of the SiC layer before and after irradiation were analyzed by load-depth curve and stress & strain.The results show that the decrease in mechanical properties of the SiC layer is closely related to the mechanical behaviors under external force.For example,the bearing capacity and plastic deforma-tion degree decrease,and the stress & strain distribution are disordered.The results provide a quantitative explanation for the irradiation behavior of the SiC layer of TRISO particles and the change of mechanical properties under irradiation.It is helpful to understand the irradiation behavior and relationship between the irradiation behavior and mechanical properties of the SiC layer.

Finite element simulation of thermal stress in RF magnetron sputtered SiC coating as tritium penetration barrier

Microstructural analysis of the thermal fatigue tested Be/CuCrZr joint with artificial defects between Ti/Cu interlayers

Simulation of the effects of different substrates, temperature, and substrate roughness on the mechanical properties of Al2O3 coating as tritium penetration barrier

Molecular Dynamics Simulation of Irradiation Behaviors and Mechanical Properties of SiC Layer of TRISO Particles

Irradiation-Thermal-Mechanical Coupling Behaviors of a Typical TRISO/SiC Fuel Element Based on Actual Distribution

Simulation of Residual Stresses and Their Effects on Thermal Barrier Coating Systems Using Finite Element Method

Primary Radiation Damage in 3C-Sic under Strain Field Studied with Molecular Dynamics Simulation

Effect of PyC Thermal Behavior on the Stress of TRISO-Coated Fuel Particles

Stochastic Simulation of Thermal Residual Stress in Environmental Barrier Coated 2.5D Woven Ceramic Matrix Composites

Corrosion of SiC layers on coated zirconia particles in wet atmosphere

Stress Analysis of Aspherical TRISO-coated Particle with X-ray Computed Tomography

A Diffusion-Coupled Cohesive Element Model for Cracking Analysis of Thermal Barrier Coatings

Influence of radio frequency magnetron sputtering parameters on the structure and performance of SiC films

Investigation of the bulging mechanism of C/SiC coating through in situ optical observation and numerical simulation

The Study of Irradiation-Induced Failure Behavior for the TRISO-coated Fuel Particle in HTGR

Study of Atomic Sputtering and Transport Dynamics by Monte Carlo Simulation

Phase Field Modeling of Irradiation-induced Shrinkage Fracture in TRISO Fuel Particle

Residual stress analysis in the Al2O3/Ti 3SiC2 multilayer composites

Stress Analysis of Aspherical Coated Particle with Inner Pressure

Comparative study on the effects of α/γ phase ratio on the micro-structures and properties in Al2O3 coatings under silicon ion irradiation

Modeling of the damage and fracture behaviors of a SiC triplex tube during the burst test with elastomeric insert