Abstract:<p>Modern hybrid rockets are susceptible to the highly ablative environment in which they operate, as introducing an adequate cooling system has so far been a challenge. Ablative material has been widely adopted for use in hybrid rockets, which can only survive for the limited operation time. The use of ablative materials such as pyrolytic composite or graphite is advantageous for use in a simple system in an uncooled state. However, ablation causes severe enlarging in the nozzle throat area and a significant drop in the pressure during operation. Recently, Ultra High-Temperature Ceramics (UHTCs) have been noted as superior in terms of ablation and oxidation resistance. The most promising HfC-SiC composite ceramic has demonstrated an enhanced performance for thermal and mechanical properties. In this study, an HfC-SiC composite was embedded in the graphite casing as a nozzle insert throat to analyze the feasibility of its application in rockets. An experimental analysis of the ablation in the HfC-SiC was carried out with a 250 N scale hybrid thruster using High Test Peroxide (HTP) and High-Density Polyethylene. The hot-fire condition was set to above 30 bar for 25 s combustion, with the purpose of producing significant erosion on the nozzle materials. The graphite nozzle of the same shape was also tested under the same experimental conditions for comparison of the erosion. The hot-fire test with the HfC-SiC insert resulted in a stable rocket performance, with improvements to the chamber pressure and the thrust, whereas the combustion performance varied undesirably in the test using the graphite nozzle due to ablation. The rate of ablation in the throat was significantly reduced to 15.81 μm/s using HfC-SiC, which is 46.5% of the erosion rate found in the graphite. The adoption of the HfC-SiC composite effectively inhibited the ablation on the throat. However, substantial erosion occurred on the interfaces due to the different ablation resistances. The feasibility of adopting hafnium-based carbide on the rocket was also evaluated based on a material analysis of the surface oxidation.</p>

Near net-shape, ultra-high melting, recession-resistant ZrC/W-based rocket nozzle liners via the displacive compensation of porosity (DCP) method

Dense Submicron-Sized ZrC – W Composite Produced by Reactive Melt in Fi Ltration at 1200 ° C

Effect of ZrC nanopowder addition in WC preforms on microstructure and properties of W–ZrC composites prepared by the displacive compensation of porosity (DCP) method

Tungsten Joining with Copper Alloy and Its High Heat Load Performance

Preparation of ablative resistance CF-ZrO 2 gradient composites by the pressure-assisted osmosis method

Microstructure and Ablation Behavior of W Coating Prepared by Atmospheric Plasma Spraying for Zr/Cu Infiltrated C/C Composites

Novel low temperature derived W f /W-ZrC-Cu composites by reactive infiltration with enhanced mechanical and thermal physical properties

Microstructure and ablation behaviour of C/C-SiC-ZrC-Cu composites prepared by reactive melt infiltration

Effects of non-uniform needled microstructure on failure mechanisms of 3D needled composites thick-walled cylinder under axial compression and internal pressure

Adhesive joint properties of advanced carbon/ceramic composite and tungsten–copper alloy for the hybrid rocket nozzle

In-situ fabrication and characterization of W-ZrC composites via pressureless reaction sintering

Development of a highly loaded zirconium carbide paste for material extrusion additive manufacturing

Investigations on an All-Oxide Ceramic Composites Based on Al2O3 Fibres and Alumina–Zirconia Matrix for Application in Liquid Rocket Engines

Ablation characteristics of rocket nozzle using HfC-SiC refractory ceramic composite

Fabrication of spherical W–ZrC powder for additive manufacturing by spray granulation combined with plasma spheroidization

Zirconium Carbide for Hypersonic Applications, Opportunities and Challenges

Effect of ZrC nano-powder addition on the microstructure and mechanical properties of binderless tungsten carbide fabricated by spark plasma sintering

Architectural Engineering Inspired Method of Preparing C-f/ZrC-SiC with Graceful Mechanical Responses

Development of High Thermal Conductivity Copper Alloys with Diamond Particle Additions

ZrC Modified Carbon/carbon Composites Using ZrSi2 and Zr-Cu Alloys As Reactive Infiltrating Materials: A Comparative Investigation

Microstructure characterization of in-situ ZrC composite coating with graceful toughness and improved tribological properties prepared by plasma spraying