Abstract:Ni-rich layered oxides have become the main force of cathode materials for EV cells with high energy density owing to their satisfactory theoretical capacity, cost-effectiveness, and low toxicity. However, the high-voltage stability of Ni-rich cathode materials still has not fulfilled the demand of power batteries due to their intrinsic structural and electrochemical instability. The commonly used modification procedures are achieved via a wet process, which may lead to surface lithium-ion deficiency, phase change, and high costs during manufacturing. Herein, we construct a multifunctional Ti-based interfacial architecture on the surface of LiNi0.6Co0.2Mn0.2O2 (NCM) cathode materials via a novel dry interface modifying process in which no solvent is employed. The Ti-based interfacial architecture accelerates the transportation of lithium ions and consequently stabilizes the interfacial structure. This approach significantly improves the cycling stability in half cells, with a 15% increase in capacity retention over 100 cycles at 1 C under a high voltage of 4.5 V. Impressively, few internal cracks are observed in a modified sample after 500 times of charge and discharge between 2.75 and 4.35 V at 1 C rate, and the capacity retention can reach 93%.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.1c12803.XRD patterns and SEM images for all samples, HRTEM image of NCM-T2, single GITT titration curves, voltage as a function of square root of time for a single charging current pulse duration with the corresponding linear fit, XRD Rietveld refinement lattice parameters, and fitted electrochemical impedance parameters (PDF)This article has not yet been cited by other publications.

Fabrication and interfacial characterization of Ni-rich thin-film cathodes for stable Li-ion batteries

Realizing Superior Cycling Stability of Ni-Rich Layered Cathode by Combination of Grain Boundary Engineering and Surface Coating

Synergistic Effect of B-Nb Co-modified to Achieve Crystal Structure and Interface Tuning for Ni-rich Cathode

Mixed-conducting Interlayer Boosting the Electrochemical Performance of Ni-rich Layered Oxide Cathode Materials for Lithium Ion Batteries

Enabling stable and high-rate cycling of a Ni-rich layered oxide cathode for lithium-ion batteries by modification with an artificial Li<SUP>+</SUP>-conducting cathode-electrolyte interphase

Chemical-Mechanical Effects in Ni-Rich Cathode Materials

Artificial interface modification of Ni-rich ternary cathode material to enhance electrochemical performance for Li-ion storage through RF-plasma-assisted technique

Tailoring electrolyte to enable high-rate and super-stable Ni-rich NCM cathode materials for Li-ion batteries

Enhanced interfacial reaction interface stability of Ni-rich cathode materials by fabricating dual-modified layer coating for lithium-ion batteries

Enhancing the Integral Structural and Thermal Stability of Ultrahigh-Ni Cathodes via Morphology Refinement and In Situ Interfacial Engineering

New insights into dry-coating-processed surface engineering enabling structurally and thermally stable high-performance Ni-rich cathode materials for lithium ion batteries

Advancing Lithium-Ion Batteries' Electrochemical Performance: Ultrathin Alumina Coating on Li(Ni0.8Co0.1Mn0.1)O2 Cathode Materials

Superior Stability Secured by a Four-Phase Cathode Electrolyte Interface on a Ni-Rich Cathode for Lithium Ion Batteries

Bifunctional Self-Assembled Molecular Layer Enables Stable Ni-rich Cathodes

Manipulation of an ionic and electronic conductive interface for highly-stable high-voltage cathodes

Stabilizing high-Ni cathodes with gradient surface Ti-enrichment

Nanoscale operation of Ni-Rich cathode surface by polycrystalline solid electrolytes Li3.2Zr0.4Si0.6O3.6 coating

Thermal Expansion Neutralization Enhancing the Cycling Stability of Ni-Rich LiNi 0.6 Co 0.2 Mn 0.2 O 2 Cathode Material

Construction of a nickel-rich LiNi 0.83 Co 0.11 Mn 0.06 O 2 cathode with high stability and excellent cycle performance through interface engineering

Stabilizing the Interphase in an Ultra-High-Nickel Cathode Enabling High-Performance Lithium-Ion Batteries

Engineering a Robust Interface on Ni-Rich Cathodes via a Novel Dry Doping Process toward Advanced High-Voltage Performance