Abstract:Since the commercialization of lithium-ion battery in 1991, it has promoted human society development for nearly three decades. Due to its higher energy density, Ni-rich layered oxides currently stand out as the most promising cathode materials to build power batteries for portable electronic devices and new energy electric vehicles. However, the severe side effects on the electrode/electrolyte interface and the structural instability of the material hinder its development, and a lot of research focus on improving the cycling stability and rate capability of nickel-rich cathode material. Here, a facile treatment with Na2PO3F was carried out to modify the Ni-rich LiNi0.83Co0.11Mn0.06O2 material at surface and bulk regions by using wet methods. By virtue of the fact that Na2PO3F dissolves in water and releases fluorine ions, a F- doped and LiF coated Ni-rich LiNi0.83Co0.11Mn0.06O2 material was obtained. The X-ray diffraction (XRD) results showed that (003) peak shifted to a higher angle due to the replacement of O2- by smaller F-. Besides, the XRD Rietveld refinement and X-ray photoelectron spectroscopy (XPS) sputtering data determined that part of F- ions had been successfully doped into the lattice, and the basic layer structure of the material was still well preserved in the process of modification. Scanning electron microscope (SEM), energy disperse spectroscopy (EDS), and transmission electron microscope (TEM) combined with XPS proved the existence of surface LiF coating layer. The 2 similar to 10 nm LiF layer was uniformly covered onto the surface of the cathode material, acting as a physical barrier against direct corrosion from the electrolyte, thus enhancing the cycling stability. In addition, the lithium ion diffusion coefficients (D-Li(+)) for bare and modified samples were calculated from cyclic voltammetry test results, which reveals a better rate capability from the synergistic effect of surface LiF coating and lattice F- doping. The electrochemical tests also showed a better cycling stability and enhanced rate capability of the modified samples: within 2.75 similar to 4.3 V, the capacity retention after 200 cycles at 1 C-rate had been elevated from 32.2% to 65.2%; the discharge capacity under 10 C-rate was also improved from 145.7 to 161.5 mAh/g. To elaborate the improved effect, post-cycling characterizations were conducted. The morphology of modified particles after 200 cycles at 1 C still maintained intact grains, in contrast with the bare samples, exhibiting many micro-cracks. XPS spectra on decorated cathodes after cycling showed weaker signals of by-products including LW, LixPOyFz, NiF2 in the CEI layer, indicating side reaction on the interface was effectively suppressed, thus contributing to enhancing the cycling stability. The applicable method herein demonstrates a promising solution for improvement of Ni-rich cathode materials and their coming commercial application.

Chemical-Mechanical Effects in Ni-Rich Cathode Materials

Radially Oriented Single‐Crystal Primary Nanosheets Enable Ultrahigh Rate and Cycling Properties of LiNi0.8Co0.1Mn0.1O2 Cathode Material for Lithium‐Ion Batteries

Synergistic Effect of B-Nb Co-modified to Achieve Crystal Structure and Interface Tuning for Ni-rich Cathode

Atomical Reconstruction and Cationic Reordering for Nickel‐Rich Layered Cathodes

Surface Atomic Rearrangement with High Cation Ordering for Ultra-Stable Single-Crystal Ni-Rich Co-Less Cathode Materials

Enabling Excellent Thermal Stability of an Ultrahigh Nickel-Rich Cathode (lini0.90co0.05mn0.05o2) by a Magnesium and Titanium Codoping Strategy

Electrochemical Performances of Nickel‐Rich Single‐Crystal LiNi0.83Co0.12Mn0.05O2 Cathode Material for Lithium‐Ion Batteries Synthesized by Tuning Li+/Ni2+ Mixing

A new high-valence cation pillar within the Li layer of compositionally optimized Ni-rich LiNi 0.9 Co 0.1 O 2 with improved structural stability for Li-ion battery

High-Performance Layered Ni-Rich Cathode Materials Enabled by Stress-Resistant Nanosheets

Modifying surface chemistry and stress concentration to enable highly stable ultrahigh-Ni cathodes

Enhancing chemomechanical stability and high-rate performance of nickel-rich cathodes for lithium-ion batteries through three-in-one modification

Rational Design of Mechanically Robust Ni-rich Cathode Materials Via Concentration Gradient Strategy

Stabilizing high-Ni cathodes with gradient surface Ti-enrichment

Lattice Engineering to Refine Particles and Strengthen Bonds of the LiNi0.9Co0.05Mn0.05O2 Cathode toward Efficient Lithium Ion Storage

Pushing High Capacity with Thermodynamically Stable Interface for Single Crystalline Nickel-rich Cathode

Lattice Engineering to Refine Particles and Strengthen Bonds of the LiNi<sub>0.9</sub>Co<sub>0.05</sub>Mn<sub>0.05</sub>O<sub>2</sub> Cathode toward Efficient Lithium Ion Storage

Tailoring electrolyte to enable high-rate and super-stable Ni-rich NCM cathode materials for Li-ion batteries

Enhanced Reversibility of Single Crystal Ni-Rich Cathode Materials Via Ti Doping

One-Step Synthesis of a Single-Crystal LiNi 0.83 Co 0.11 Mn 0.06 O 2 Cathode with Excellent Electrochemical Properties by Ti 4+ Doping and LiTi 2 O 4 In Situ Chemical Coating Using a Novel Variable Temperature Sintering Process

Dual-Decoration and Mechanism Analysis of Ni-rich LiNi0.83Co0.11Mn0.06O2 Cathodes by Na2PO3F

Surface-to-bulk Engineering with High-Valence W6+ Enabling Stabilized Single-Crystal LiNi0.9Co0.05Mn0.05O2 Cathode