Abstract:Despite significant efforts to develop ultra-high temperature ceramics, the phase stability together with high hardness and oxidation resistance remains to be addressed in ZrB2-SiC based ceramics. ZrB2-20 vol% SiC (ZS20) ceramics with varying amounts of Si3N4 (2.5, 5 and 10 vol%) were processed by multi stage Spark Plasma Sintering (SPS) over a range of temperature (1800–1900 °C) for 3 min under 50 MPa. All the ZS20-Si3N4 composites could be densified to more than 98% theoretical density (ρth) after SPS at 1900 °C. The XRD, SEM-EDS analysis of the ZS20-Si3N4 composites revealed the presence of reaction product phases (ZrO2, BN, ZrN) along with SiC and ZrB2 major phases. Sintering reactions were proposed to explain the existence of such new phases and extinction of Si3N4. Thermo-Calc software was also used to further confirm the formation of these new phases in the ZS20-Si3N4 samples. The hardness of ZS20-Si3N4 composites varied between 25.50 and 30.56 GPa, in particular, ZrB2-20 vol% SiC-5vol% Si3N4 measured with the maximum hardness. In fact, it is the highest ever reported hardness for the ZrB2 composites. Considering oxidation resistance, the weight gain of ZrB2-20 vol%SiC composites decreased (from 13.84 to 9.84 mg/cm2) and oxide layer thickness increased (64–128 μm) after oxidation at 1500 °C for 10 h in air. The cross sectional microstructure of oxidized ZS20-Si3N4 composites consists of thick dense outer layer of SiO2, intermediate (ZrO2-SiO2) layer and unreacted bulk. The formation of dense SiO2 layer and absence of SiC depleted layer from the oxidized samples are signatures of improved oxidation resistance of Si3N4 reinforced ZrB2-20 vol% SiC.

Plasma Oscillatory Pressure Sintering of Mo-9Si-8B Alloy with ZrB2 Addition

Optimization of microstructure and mechanical properties of oscillatory pressure sintered ZrO<sub>2</sub>-Al<sub>2</sub>O<sub>3</sub>-SiCp ceramics

Microstructure and Mechanical Properties of ZTA Composites Fabricated by Oscillatory Pressure Sintering

Microstructural evolution and mechanical properties of ZrO<sub>2</sub> (3Y)-Al<sub>2</sub>O<sub>3</sub>-SiC(<sub>w</sub>) ceramics under oscillatory pressure sintering

Optimization of microstructure and mechanical properties of oscillatory pressure sintered ZrO2–Al2O3-SiCp ceramics

Fabrication and Mechanical Properties of ZrO2–Al2O3–SiC(w) Composites by Oscillatory Pressure Sintering

Microstructures and mechanical properties of reactive spark plasma-sintered ZrB2–SiC–MoSi2 composites

Effects of SiC Platelet and ZrSi2 Additive on Sintering and Mechanical Properties of ZrB2-based Ceramics by Hot-Pressing

An Oscillatory Pressure Sintering of Zirconia Powder: Densification Trajectories and Mechanical Properties

Spark plasma sintering and hot pressing of ZrB2–SiCW ultra-high temperature ceramics

Phase stability, hardness and oxidation behaviour of spark plasma sintered ZrB2-SiC-Si3N4 composites

Improved Mechanical Properties of Al2O3-25 Vol% SiCw Composites Prepared by Oscillatory Pressure Sintering

A Novel Approach to Improve Flexural Strength of Al2O3‐20 Wt% ZrO2 Composites by Oscillatory Pressure Sintering

The process and mechanical properties of Nb–Si–Mo–Ti alloy prepared by spark plasma sintering

Study on the Pre-Oxidation and Resulting Oxidation Mechanism and Kinetics of Mo-9Si-8B Alloy

Affordable spark plasma sintering of superhard Al-doped ZrB 2 nanoceramics from ZrH 2 , B, and Al mechanically activated by shaker milling

Preparation and Mechanical Properties of Laminated Zirconium Diboride/molybdenum Composites Sintered by Spark Plasma Sintering

Influence of bismuth oxide as a sintering aid on the densification of cold sintering of zirconia

Synergistic strengthening and toughening of oscillatory pressure sintered WC-ZrO2-Al2O3 ceramics

Doping N/O Impurities into a MoNbTiWZr Refractory Multi-Principal Element Alloy and the Strengthening Mechanism

Preparation of Zirconia Ceramics with High Density and Fine Grains by Oscillatory Pressure Sintering