Abstract:To enhance the low-temperature plasticity and high-temperature strength of molybdenum alloys, we introduce a method of uniformly dispersing nano-ZrTiO4 particles within and between molybdenum grains. This approach effectively eliminates the formation of hard agglomerations between particles and leads to a further refinement of molybdenum grains. The research employs molecular level solid-liquid doping and subsequent liquid dispersion evaporation techniques to successfully synthesize Mo-ZrTiO4 nano-composite powder following H2 reduction. Subsequently, a novel fine-grained Mo-ZrTiO4 alloy sintered billet is successfully fabricated through cold isostatic pressing and high-temperature sintering. To assess the efficacy of the process, three sets of comparative experiments are designed, each employing different methods. The comparative studies have revealed compelling advantages of the liquid dispersed evaporated fine-grained samples of Mo-ZrTiO4. The key advantages identified are as follows:the samples demonstrate a refined grain size, ranging from 2 mu m to 4 mu m. Within the samples, the nano ZrTiO4 particles have an average size of approximately 200 nm. The density and Vickers hardness of the samples is measured at 10.21 g/cm3 and 268.5 +/- 17HV0.2, respectively. The samples exhibit impressive toughness even at room temperature, notably, the high-temperature compressive strength of these samples surpasses that of the deformed samples reported in previous literature concerning this system. The mechanism of liquid dispersion evaporation method in grain nucleation, growth, and powder drying, reduction, and sintering processes was systematically elaborated. Simultaneously, a detailed analysis was conducted on two high-temperature strengthening mechanisms that impact the mechanical properties. The results indicate that this excellent performance can be attributed to the synergistic effect of both fine grain strengthening and uniform dispersion strengthening of second-phase nanoparticles.

Doping N/O Impurities into a MoNbTiWZr Refractory Multi-Principal Element Alloy and the Strengthening Mechanism

Investigation of a Hot-Pressed Nb–Ti–Al Alloy: Mechanical Alloying, Microstructure and Mechanical Property

Evaluation of tensile property and strengthening mechanism of Zirconia reinforced molybdenum alloy

Strong and Ductile Niobium-Based Refractory Alloy Via Deformable Zirconia Nanoparticles

Microstructure and Properties of Novel Quinary Multi-Principal Element Alloys with Refractory Elements

Microstructure, Mechanical Properties, and Strengthening Mechanisms of Nanostructural Y-Zr-O Oxide Dispersion-Strengthened (ODS) Mo Alloys

The Multi-Scale Microstructure and Strengthening Mechanisms of Mo-12Si-8.5BxZr (at.%) Alloys

Additive Manufacturing of Refractory Multi-Principal Element Alloy with Ultrahigh-Temperature Strength Via Simultaneous Enhancements in Printability and Solid Solution Hardening

Microstructures and mechanical properties of a precipitation hardened refractory multi-principal element alloy

Improving mechanical properties of W-Ni 3 Al alloy through Zr element addition: Solid-solution and oxide particle strengthening

Enhancing the Strength and Plasticity of Laser Powder Bed Fused NbMoTaW Refractory High-Entropy Alloy Via Ti Alloying

High Strength-Ductility Synergy in Refractory Multi-Principal Element Alloys Via Special Deformation Mechanisms and Dislocation Behaviors

Complex strengthening mechanisms in the NbMoTaW multi-principal element alloy

Mechanical properties and strengthening mechanism of the nano-sized m-ZrO 2 ceramic particle reinforced NbMoTaW refractory high-entropy alloy

Study on mechanical alloying behavior and thermal stability of HfMoNbTaTi refractory high-entropy alloy

Synthesis of TiAl/Nb Composites with Concurrently Enhanced Strength and Plasticity by Powder Metallurgy

Microstructure and high-temperature deformation performance of liquid-dispersed evaporated Nano-ZrTiO4 doping molybdenum alloy

An excellent synergy in yield strength and plasticity of NbTiZrTa 0.25 Cr 0.4 refractory high entropy alloy through the regulation of cooling rates

Influence of Γ′ Precipitate on Impact Toughness and Tensile Properties of a New Fe–Ni-based Superalloy

Achieving ultra-strong and ductile CoNi-based FCC multi-principal element alloys via alloying with refractory Mo and W

Microstructure Characteristics and Mechanical Properties of Hf0.5Mo0.5NbTiZr Refractory High Entropy Alloy with Cr Addition