Abstract:The primary objective of this study is to fabricate an Al-12wt. % Si Alloy/ZrO2 composite using the Stir Casting technique, with a specific focus on assessing its performance, particularly in terms of wear characteristics. This research presents a unique approach by utilizing Al-12wt. % Si Alloy as the matrix material, aiming to develop tailored Al Alloy matrix composites suitable for applications requiring enhanced tribological properties. The composites are systematically manufactured with varying percentages of micro-sized ZrO2 reinforcements, specifically 0.5, 1, and 3wt. %. The incorporation of ZrO2 results in significant improvements in wear resistance, a critical attribute for Al-12wt. % Si Alloy-based composites. These composites find extensive utility across industries such as marine, aerospace, automotive, and the power sector, where they are indispensable for producing vital components like electrical sliding contacts, gears, bearings, bushes, pistons, piston rings, and clutches. Despite the availability of various promising reinforcement materials, researchers persistently explore novel combinations of matrices and reinforcements to tailor properties and enhance cost-effectiveness. ZrO2 has emerged as a notable reinforcement material in metal matrix composites, as evidenced by numerous research endeavours. The composites fabricated with ceramic reinforcement's exhibit enhanced tribological characteristics. The study observes that the wear rate decreases up to 3 wt. % of reinforcements, beyond which it increases due to reinforcement agglomeration. The optimal wear-resistant combination is found at 3 wt. % of ZrO2, attributed to robust micro-coring and interstitial metal-oxygen bonding facilitated by the Si content in the Al-12%Si matrix. The results are further optimized using Response Surface Methodology (RSM) techniques and validated using the ANOVA table to elucidate the behaviour of the composites under different operational conditions. The hardness results further ascertain the decrease in the wear rate due to the inclusion of ZrO2 reinforcements owing to micro coring and strengthening.

Effects of Some Material and Experimental Variables on the Slurry Wear Characteristics of Zinc-Aluminum Alloys

Wear Behaviour and Microstructural Changes of SiCw-Al Composite under Unlubricated Sliding Friction

Abrasive wear characteristics of a zinc-based alloy and zinc-alloy/SiC composite

Effects of silicon content and test conditions on the dry wear behaviour of Zn–30Al–3Cu–(0–5)Si Alloys

Dry Sliding Wear Behaviour of Al–7.6Si–xZr Alloys: Understanding the Impact of Zr on Wear Characteristics, Mechanics, and Transition

Dry sliding wear characteristics of some zinc-aluminium alloys: a comparative study with a conventional bearing bronze at a slow speed

Wear Properties Analysis on Al-Based Automotive Alloy with Varied Levels of Si in Dry, 3.5% NaCl and Seawater Corrosive Environments

Effect of Alloying Elements on the Dry Sliding Wear Characteristics of Gravity-Cast Mg-Sn Based Alloys

Corrosive Wear of Alumina Particles Reinforced Al–Si Alloy Composites

Tribological behaviour of hypereutectic Al-Si automotive cylinder liner material under dry sliding wear condition in severe wear regime

Wear behavior of Mg–10Y–4Gd–1.5Zn–0.4Zr alloy

Dry sliding wear of microalloyed Er-containing Al–10Sn–4Si–1Cu alloy

Experimental and Theoretical Analysis of Zircaloy-4 and AISI 304 Stainless Steel Material Pair in Water Sliding Conditions

Effect of Heat Treatment on the Dry Sliding Wear Behavior of the Mg-3Zn-0.4Ca Alloy for Biodegradable Implants

Study on Dry Sliding Wear and Friction Behaviour of Al7068/Si3N4/BN Hybrid Composites

Effect of impingement angle and impact velocity on slurry erosive wear behaviour of particulate reinforced aluminium composites

CHARACTERIZATION OF WEAR RATE OF Al-12WT. %Si ALLOY BASED MMC REINFORCED WITH ZrO2 PARTICULATES

Unidirectional dry sliding wear analysis of ZE41 magnesium alloy

Dry sliding wear behaviour of AZ31 magnesium alloy strengthened by nanoscale SiCp

A comparison of the wear of polymers and metal alloys in laboratory and field slurries

Effect of Heat Treatment on Tribological Properties of SiCp/Al–Mg–Mn–Cu Aluminum Matrix Composites