Abstract:The effect of solo and combined addition of Al (3wt. %) and Zn (1wt. %) into gravity-cast Mg-10 wt. % Sn binary alloy on the dry sliding wear test has been investigated using pin-on-disk configuration with varying rotational speed (100 and 200 rpm) under a range of test loads (10, 20, 30, and 40 N). Microstructural characterization and phase analysis of the as-cast Mg-Sn alloys using scanning electron microscope and x-ray diffraction, respectively, have revealed the refinement of the binary alloy microstructure in terms of smaller dendritic arm spacing, uniform and discrete distribution of eutectic phase mixture at the interdendritic locations owing to the alloying additions. Moreover, a significant improvement in microhardness is achieved with increase in amount (wt.%) of alloying elements, depicting the highest hardness in the Mg-10Sn-3Al-1Zn (wt.%) alloy. Simultaneously, the alloying addition even in micro-concentration has been found to reduce the specific wear rate than that of the binary alloy over the entire loading range. The post-wear topographical surface features and chemical analysis using scanning electron microscope and energy-dispersive x-ray spectroscopy of the investigated alloys have suggested the oxidation and abrasion as dominant wear mechanisms. The reduced wear rates in the Al containing alloys are ascribed to the protective and continuous mechanically mixed oxide scale formation during test, which acts as a lubricating layer between the pin and the rotating disk. The discrete oxide island formation at the Zn-lean regions of Zn containing alloys is responsible for their accelerated wear rates.

Effect of Heat Treatment on the Dry Sliding Wear Behavior of the Mg-3Zn-0.4Ca Alloy for Biodegradable Implants

Microstructure and Wear Behavior of Heat-Treated Mg-1Zn-1Ca Alloy for Biomedical Applications

Degradation Behavior and Mechanical Integrity of a Mg-0.7Zn-0.6Ca (wt.%) Alloy: Effect of Grain Sizes and Crystallographic Texture

The Influence of Zn Content on the Corrosion and Wear Performance of Mg-Zn-Ca Alloy in Simulated Body Fluid

Effect of Alloying Elements on the Dry Sliding Wear Characteristics of Gravity-Cast Mg-Sn Based Alloys

Effect of Ultrasonic Surface Rolling Process on Wear Behavior of Mg-15Gd-1Zn-0.4Zr Alloy

Effect of Cold Deformation on Low Speed Sliding Wear of Al-10Ti Alloy

Study on microstructure and tribological behavior of the selective laser melted MgZnCa alloy

Unidirectional dry sliding wear analysis of ZE41 magnesium alloy

Sliding and Fretting Wear Behavior of Biomedical Ultrafine-Grained TiNbZrTaFe/Si Alloys in Simulated Physiological Solution

Effect of Heat Treatment on the Frictional Wear Properties of Zr-Based Amorphous Alloy

Effect of load and sliding velocity on wear behaviour of magnesium AZ91D composites reinforced with Ca 2 SiO 4 at ambient temperature

Wear characteristics of Ti–Nb–Ta–Zr and Ti–6Al–4V alloys for biomedical applications

Effects of silicon content and test conditions on the dry wear behaviour of Zn–30Al–3Cu–(0–5)Si Alloys

Dry sliding wear behavior of cast Mg–11Y–5Gd–2Zn magnesium alloy

Effects of Ultrasonic Surface Rolling Processing and Subsequent Recovery Treatment on the Wear Resistance of AZ91D Mg Alloy

Effect of Zr content on microstructure and wear behavior of Al-Si-Cu-Ni Mg-Zrx alloy

Dry sliding wear of microalloyed Er-containing Al–10Sn–4Si–1Cu alloy

Effect of microstructural and texture evolution of ECAP-processed Mg-Zn-Zr alloy on the corrosion and wear behaviours for bone repair applications

Tuning biodegradability, bone-bonding capacity, and wear resistance of zinc-30% magnesium intermetallic alloy for use in load-bearing bone applications

The microstructural characterization and wear behavior of Mg-Zn-Ce alloy with trace Ca addition