Abstract:In this study, the correlation between the microstructure and tribological performance of Sc and Zr-modified Al–Mg alloy (Scalmalloy®) samples produced via laser powder bed fusion process was evaluated via a dry sliding Pin-on-Disc wear test under different planes, directions, and various normal applied loads. The results revealed a remarkable dependency of wear properties on the as-built microstructure so that different behaviors were observed along the scanning and building planes. The microstructural examination indicated the presence of bi-modal grains and finely shaped equiaxed grains observed in the building and scanning planes, respectively. Increasing the applied loads from 20 to 40 N led to a significant increase in the coefficient of friction (COF) while increasing the load from 40 to 60 N, slightly decreasing the COF for the studied samples. No dependency was found between the COF and the corresponding microstructure at the highest applied load. The anisotropic wear resistance and COF values were predominant at the lowest applied load. Due to tailored as-built microstructural features and different microhardness values, lower wear rates were noticed along the scanning plane for all applied loads. Under the 20 N applied load, however, the worn surface of the scanning plane showed a clearer and smoother surface compared to the building plane surfaces. Ultra-fine equiaxed grains along the scanning plane and columnar grains along the building plane were determined as the main factors creating anisotropic tribological behavior. The outcomes of this study can pave the way toward producing more wear-resistant surfaces and developing components for critical wear applications in as-built conditions with no need for expensive and time-consuming surface treatments.

Study on microstructure and tribological behavior of the selective laser melted MgZnCa alloy

Microstructure and Mechanical Properties of Selective Laser Melted Mg-9 Wt%al Powder Mixture

Study of the microstructure and wear properties of Ti-12Mo-6Zr-2Fe alloy fabricated via selective laser melting

Wear and Corrosion Properties of 316L-SiC Composite Coating Deposited by Cold Spray on Magnesium Alloy

The microstructural characterization and wear behavior of Mg-Zn-Ce alloy with trace Ca addition

Surface modification of biomedical Mg-Ca and Mg-Zn-Ca alloys using selective laser melting: Corrosion behaviour, microhardness and biocompatibility

Microstructure-induced anisotropic tribological properties of Sc-Zr modified Al–Mg alloy (Scalmalloy®) produced via laser powder bed fusion process

Selective Laser Melting of Mg-Zn Binary Alloys: Effects of Zn Content on Densification Behavior, Microstructure, and Mechanical Property

Microstructure and mechanical properties of high strength Mg−15Gd−1Zn−0.4Zr alloy additive-manufactured by selective laser melting process

Effects of magnesium on microstructure, properties and degradation behaviors of zinc-based alloys prepared by selective laser melting

The Influence of Zn Content on the Corrosion and Wear Performance of Mg-Zn-Ca Alloy in Simulated Body Fluid

Wear Behavior of a Heat-Treatable Al-3.5Cu-1.5Mg-1Si Alloy Manufactured by Selective Laser Melting

Selective Laser Melting of Al-7Si-0.5 Mg-0.5Cu: Effect of Heat Treatment on Microstructure Evolution, Mechanical Properties and Wear Resistance

Mechanical Properties of High Mg-Content Al-Mg-Sc-Zr Alloy Fabricated by Selective Laser Melting

Wear and corrosion of an additively-manufactured AlMgScZrMn alloy

Microstructure, metallurgical defects and hardness of Al–Cu–Mg–Li–Zr alloy additively manufactured by selective laser melting

Densification, Microstructure and Anisotropic Corrosion Behavior of Al-Mg-Mn-Sc-Er-Zr Alloy Processed by Selective Laser Melting

Microstructures and mechanical properties of Si and Zr modified Al–Zn–Mg–Cu alloy-A comparison between selective laser melting and spark plasma sintering

Microstructure evolution and mechanical properties of Al-Al2O3 composites fabricated by selective laser melting

Selective laser melting of Al-3.48Cu-2.03Si-0.48Sc-0.28Zr alloy: Microstructure evolution, properties and metallurgical defects

Tensile property and microstructure of Al−4.77Mn−1.37Mg−0.67Sc−0.25Zr alloy under different selective laser melting processing parameters