Abstract:The Mg-11Gd-2Zn-0.4Zr (GZ112K, wt.%) alloys fabricated by selective laser melting (SLM) still contain some hard and brittle beta-(Mg,Zn)(3)Gd eutectic phase with an area fraction of 4.86% despite the ultra-fast cooling rate of SLM process, so post heat treatment is necessary. The effects of different solution conditions and aging heat treatment on microstructure and mechanical properties of the SLMed GZ112K alloys were systematically analyzed. The results show that the optimized solution condition (400 degrees C x 12 h) for the SLMed GZ112K alloys can not only transform hard and brittle beta-(Mg,Zn)(3)Gd eutectic phase into relatively softer lamellar 14H type long period stacking order (LPSO) structure leading to the improved elongation (EL) of the SLM-T4 alloys, but also retain the fine grains of the SLMed GZ112K alloys to a large extent with a small average grain size of 3.1 mu m in the SLM-T4 state contributing to the high yield strength (YS) of the SLM-T4 and SLM-T6 GZ112K alloys. After peak aging heat treatment, basal gamma ' precipitates or lamellar 14H-LPSO structure and dense prismatic elliptical 13 ' precipitates coexist in the SLM-T6 GZ112K alloys. As a result, the SLM-T6 GZ112K alloys exhibit YS of 343 +/- 9 MPa, ultimate tensile strength (UTS) of 371 +/- 4 MPa and EL of 4.0 +/- 0.05%, while those of the SLMed GZ112K alloys are 332 +/- 3 MPa, 351 +/- 5 MPa and 8.6 +/- 1.0%. The ultra-high YS of SLM-T6 GZ112K alloys results from the fine grain strengthening, the precipitation strengthening from 13 ' aging precipitates, the secondary phase strengthening from LPSO structure and X phase and the extra composite strengthening from the coexistence of basal and prismatic precipitates. The findings indicate that appropriate post heat treatment is an effective scheme for modifying microstructure and mechanical properties of the SLMed alloys.

Microstructure and mechanical properties of high strength Mg−15Gd−1Zn−0.4Zr alloy additive-manufactured by selective laser melting process

Fabrication of High-Strength Mg-Gd-Zn-Zr Alloy Via Selective Laser Melting

Investigations on Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn-Zr-Nd Alloy

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Effect of Heat Treatment on Microstructure Evolution and Mechanical Properties of Selective Laser Melted Mg-11Gd-2Zn-0.4Zr Alloy

Influence of friction stir processing and aging heat treatment on microstructure and mechanical properties of selective laser melted Mg-Gd-Zr alloy

Microstructures and Mechanical Properties of Mg-10Gd-3Y-2Zn-0.5Zr Alloy

Microstructures and Mechanical Properties of a High-Strength Mg-3.5Sm-0.6Zn-0.5Zr Alloy

Microstructure evolution and mechanical properties of a high-strength Mg-10Gd-3Y–1Zn-0.4Zr alloy fabricated by laser powder bed fusion

Microstructure evolution and mechanical properties of an ultra-high strength casting Mg–15.6Gd–1.8Ag–0.4Zr alloy

Effect of Zn Addition on Microstructure and Mechanical Properties of Mg–9Gd–3Y–0.5Zr Alloy

Selective Laser Melted High Mg‐Content Al–Si–Mg–Zr Aluminum Alloy with the Formation of Stacking Faults

Exceptional Strength Paired with Increased Cold Cracking Susceptibility in Laser Powder Bed Fusion of a Mg-RE Alloy

Tensile property and microstructure of Al−4.77Mn−1.37Mg−0.67Sc−0.25Zr alloy under different selective laser melting processing parameters

Microstructure and Mechanical Properties of Laser Melting Deposited GW103K Mg-RE Alloy

Selective Laser Melting of Mg-Zn Binary Alloys: Effects of Zn Content on Densification Behavior, Microstructure, and Mechanical Property

Achieving Ultra-High Strength and Ductility in Mg–9Al–1Zn–0.5Mn Alloy Via Selective Laser Melting

Effect of Al3(Sc, Zr) and Mg2Si Precipitates on Microstructure and Tensile Properties of Selective Laser Melted Al-14.1Mg-0.47Si-0.31Sc-0.17Zr Alloy

Effect of Solid Solution and Aging Treatments on the Microstructures Evolution and Mechanical Properties of Mg–14Gd–3Y–1.8Zn–0.5Zr Alloy

Microstructural evolution and enhanced mechanical properties of Mg–Gd–Y–Zn–Zr alloy via centrifugal casting, ring-rolling and aging

Effects of Gd and Zr Additions on the Microstructures and High-Temperature Mechanical Behavior of Mg–Gd–Y–Zr Magnesium Alloys in the Product Form of a Large Structural Casting