Abstract:Selective laser melting (SLM) of aluminium alloys is of research interest due to its potential benefits in fabricating complex components for aerospace and automotive industries. In order to improve the mechanical properties and demonstrate the credibility of selective laser melted (SLMed) Al alloys, the effects of post heat treatment on the microstructures and mechanical properties need to be studies. In the present work, the nano-TiB2 decorated Al–7Si–Cu–Mg samples were successfully fabricated using the SLM technique, and then post-treated by direct ageing and conventional T6 heat treatment. The as-built TiB2/Al–7Si–Cu–Mg sample exhibits fine equiaxed grain structures without preferred crystallographic texture due to the high cooling rate of SLM and the addition of nano-TiB2 particles. Nano-scale eutectic Si cells are present within the equiaxed grains. Inside the cells, there are dislocation tangles without precipitates. After direct ageing treatment, the grain and cell structures remain almost unchanged, and the new Al2Cu, Mg2Si, and Si phases are formed around the dislocations. While after T6 treatment, the fine grains grow up and the eutectic Si phases coarse leading to the broken of cell structures. Besides, the as-built TiB2/Al–7Si–Cu–Mg samples show high tensile strength and ductility (yield strength: 297.2 MPa, ultimate tensile strength: 474.6 MPa, elongation: 13.4%). During ageing, the yield strength is enhanced by ~35% due to precipitation hardening effect. While the broken of fine microstructure during T6 leads to the decrease of yield strength by ~16%. The microstructure development and preliminary strengthening mechanism were discussed. The effect of post-heat treatments can yield the SLMed TiB2/Al–7Si–Cu–Mg samples with appropriate mechanical properties, promoting a wide range of applications.

Selective Laser Melting of Al-7Si-0.5 Mg-0.5Cu: Effect of Heat Treatment on Microstructure Evolution, Mechanical Properties and Wear Resistance

Wear Behavior of a Heat-Treatable Al-3.5Cu-1.5Mg-1Si Alloy Manufactured by Selective Laser Melting

Microstructure, heat treatment and mechanical properties of TiB2/Al–7Si–Cu–Mg alloy fabricated by selective laser melting

Selective laser melting of Al-3.48Cu-2.03Si-0.48Sc-0.28Zr alloy: Microstructure evolution, properties and metallurgical defects

Microstructure and Mechanical Properties of Selective Laser Melted Mg-9 Wt%al Powder Mixture

Effect of Heat Treatment on Microstructure and Properties of Selective Laser Melting AlSi10Mg Alloy

Achieving high strength in selective laser melting AlSi10Mg alloy by adding microsized pure Cu particles

Selective Laser Melting of Al-Zn-Mg-Cu: Heat Treatment, Microstructure and Mechanical Properties

Effect of cooling rates and heat treatment time on Si phase of AlSi10Mg alloy manufactured by selective laser melting: Microstructure evolution and strengthening mechanism

Effect of heat treatment on microstructure, hardness and corrosion resistance of 7075 Al alloys fabricated by SLM

Effect of laser power on microstructures and properties of Al-4.82Mg-0.75Sc-0.49Mn-0.28Zr alloy fabricated by selective laser melting

Selective Laser Melting of Al-Cu-Mn-Mg Alloys: Processing and Mechanical Properties

Influence of Annealing on Mechanical Properties of Al-20Si Processed by Selective Laser Melting

Effect of Al3(Sc, Zr) and Mg2Si Precipitates on Microstructure and Tensile Properties of Selective Laser Melted Al-14.1Mg-0.47Si-0.31Sc-0.17Zr Alloy

Microstructure, wear and residual stresses of selective laser melting AlSi10Mg solid cylinder

The AlSi10Mg Samples Produced by Selective Laser Melting: Single Track, Densification, Microstructure and Mechanical Behavior

Effect of T6 Heat Treatment on the Surface Tribological and Corrosion Properties of AlSi10Mg Samples Produced by Selective Laser Melting

Microstructure evolution and mechanical properties of Al-Al2O3 composites fabricated by selective laser melting

Microstructure, Mechanical Properties, and Fatigue Fracture Characteristics of High-Fracture-Resistance Selective Laser Melting Al-Ni-Cu Alloys

The Effect of Silicon Phase Morphology on Microstructure and Properties of AlSi10Mg Alloys Fabricated by Selective Laser Melting

Mechanical Properties of High Mg-Content Al-Mg-Sc-Zr Alloy Fabricated by Selective Laser Melting