Abstract:The primary objective of this study is to fabricate an Al-12wt. % Si Alloy/ZrO2 composite using the Stir Casting technique, with a specific focus on assessing its performance, particularly in terms of wear characteristics. This research presents a unique approach by utilizing Al-12wt. % Si Alloy as the matrix material, aiming to develop tailored Al Alloy matrix composites suitable for applications requiring enhanced tribological properties. The composites are systematically manufactured with varying percentages of micro-sized ZrO2 reinforcements, specifically 0.5, 1, and 3wt. %. The incorporation of ZrO2 results in significant improvements in wear resistance, a critical attribute for Al-12wt. % Si Alloy-based composites. These composites find extensive utility across industries such as marine, aerospace, automotive, and the power sector, where they are indispensable for producing vital components like electrical sliding contacts, gears, bearings, bushes, pistons, piston rings, and clutches. Despite the availability of various promising reinforcement materials, researchers persistently explore novel combinations of matrices and reinforcements to tailor properties and enhance cost-effectiveness. ZrO2 has emerged as a notable reinforcement material in metal matrix composites, as evidenced by numerous research endeavours. The composites fabricated with ceramic reinforcement's exhibit enhanced tribological characteristics. The study observes that the wear rate decreases up to 3 wt. % of reinforcements, beyond which it increases due to reinforcement agglomeration. The optimal wear-resistant combination is found at 3 wt. % of ZrO2, attributed to robust micro-coring and interstitial metal-oxygen bonding facilitated by the Si content in the Al-12%Si matrix. The results are further optimized using Response Surface Methodology (RSM) techniques and validated using the ANOVA table to elucidate the behaviour of the composites under different operational conditions. The hardness results further ascertain the decrease in the wear rate due to the inclusion of ZrO2 reinforcements owing to micro coring and strengthening.

Corrosive Wear of Alumina Particles Reinforced Al–Si Alloy Composites

Fabrication and performance of Ni-Co-P/Si3N4 electroplated composite coatings on al-si alloys

Wear Behaviour and Microstructural Changes of SiCw-Al Composite under Unlubricated Sliding Friction

Wear and abrasion of cast Al-Alumina particle composites

Wear Properties Analysis on Al-Based Automotive Alloy with Varied Levels of Si in Dry, 3.5% NaCl and Seawater Corrosive Environments

A comparison of the erosive wear performance of particle reinforced aluminum matrix composites

Microstructural, mechanical and corrosion behaviour of Al–Si alloy reinforced with SiC metal matrix composite

Enhancing microstructural, tribological and corrosion responses of Al–Zn–Mg–Cu alloy via nano-/micro-Al2O3 particulates

Abrasive wear of alumina fibre-reinforced aluminium

Influence of silicon nitride (Si3N4) reinforcement on mechanical properties and wear behaviour of AZ31–Nano alumina (Al2O3) composites developed through the stir casting route

Effect of Si3N4 Ceramic Particulates on Mechanical, Thermal, Thermo-Mechanical and Sliding Wear Performance of AA2024 Alloy Composites

Microstructural Evolution, Tensile Failure, Fatigue Behavior and Wear Properties of Al2O3 Reinforced Al2014 Alloy T6 Heat Treated Metal Composites

Wear-resistance mechanism of an Al–12Si alloy reinforced with aluminosilicate short fibers

Effects of Some Material and Experimental Variables on the Slurry Wear Characteristics of Zinc-Aluminum Alloys

Study of Wear Behavior on AA6061 Reinforced with Hybrid Ceramic Composites through Optimization

Corrosion suppression and strengthening of the Al-10Zn alloy by adding silica nanorods

STUDY OF MECHANICAL PROPERTIES AND WEAR BEHAVIOR OF ALUMINUM MATRIX COMPOSITES REINFORCED WITH SILICON CARBIDE PARTICLES

Metallographic Study and Sliding Wear Optimization of Nano Si3N4 Reinforced High-Strength Al Metal Matrix Composites

CHARACTERIZATION OF WEAR RATE OF Al-12WT. %Si ALLOY BASED MMC REINFORCED WITH ZrO2 PARTICULATES

Enriching mechanical, wear, and corrosion behaviour of SiO2/TiO2 reinforced Al 5754 alloy hybrid composites

Influence of Al2O3 reinforcement on the abrasive wear characteristic of Al2O3/PA1010 composite coatings