Abstract:The purpose of this study is to quantitatively analyze the effect of strain path on roughness evolution of free surface during plastic deformation. Firstly, the crystal plastic finite element model for a representative volume element (RVE) of polycrystalline is established, including the polycrystalline geometric model and initial topography model. Next, based on two groups of strain path including five typical strain paths, i.e., uniaxial tension (UT), biaxial tension (BT), plane strain tension (PST), plane strain compression (PSC) and in-plane pure shear (PPS), the 3D surface roughness of free surface after the plastic deformation is presented quantitatively. The total change of surface topography can be divided into two parts, which relate to the homogenous deformation and inhomogeneous deformation. In a simple manner, the homogenous deformation and inhomogeneous deformation can correspond with the elastic deformation and plastic deformation respectively. As in the elastic deformation, the effect of the misorientation of the adjacent grains and strain localization in the polycrystalline material on the surface topography has no chance to exert on the very small strain. So the inhomogeneity of polycrystalline material has been ignored in the elastic deformation. For the effect of homogeneous deformation, the relationship between the surface roughness of the deformed surface, initial roughness and strain path is analytically derived. For the contribution of the inhomogeneous deformation to surface roughening, the quantitative relationship between surface roughness of the deformed surface and the strain path is acquired by the mathematical fitting based on hundreds of crystal plasticity finite element simulations. The final surface roughness of the deformed surface is obtained by combining these two parts. Then the experiment of biaxial tension on 6061 aluminum alloy sheet is taken as an example to verify the accuracy of surface roughness calculation. The comparison of experimental results and calculated results shows good consistency. Thereafter the surface roughening phenomena in the plastic deformation are observed at three different scales. The homogeneous deformation does not form additional peaks and valleys but changes the spacing and height of peaks and valleys of the initial surface topography, which brings about the surface roughening at macroscale level. In inhomogeneous deformation, the misorientation of the adjacent grains in the polycrystalline material is taken into consideration, which leads to the grain rotation and generates the additional peaks and valleys of the initial surface topography. The surface roughening due to this part can be seen at the mesoscopic scale. And the step phenomenon caused by slip bands inner the grains is the microscopic scale roughening behavior. This work is beneficial to understand the roughness evolution of free surface quantitatively with the effect of strain path and make out the surface roughening phenomena at different scales.

Experimental and Numerical Investigation of Mesoscale Deformation-Induced Surface Roughening in Polycrystalline Metals and Alloys (Review)

Deformation-Induced Surface Roughening of an Aluminum–Magnesium Alloy: Experimental Characterization and Crystal Plasticity Modeling

Finite Element Simulation of Surface Deformation of Polycrystal with a Rough Surface under Repeated Load

A review on plastic deformation induced surface/interface roughening of sheet metallic materials

Surface Roughness Evolution under Constant Amplitude Fatigue Loading Using Crystal Plasticity

Achieving High Strength and High Ductility in Nanostructured Metals: Experiment and Modelling

On the evolution of surface roughness during deformation of polycrystalline aluminum alloys

Numerical Study of Effect of Surface Roughness on Superelastic Behaviour of Shape Memory Alloy

Research Status of Surface Roughening during Plastic Deformation

On the Study of the Initiation of the Micro Crack on the Smooth Surface of Polycrystalline

Effect of Strain Path on Roughness Evolution of Free Surface During Plastic Deformation

Effect Mechanism and Equivalent Model of Surface Roughness on Fatigue Behavior of Nickel-Based Single Crystal Superalloy

Surface Roughening Behavior and Mechanism in Aluminum Alloy Under Tensile Deformation

Phenomenological Anisotropic Study of Surface Finish in Pack Rolling

Quantitative Analysis of Surface Roughness Evolution in FCC Polycrystalline Metal During Uniaxial Tension

Analysis of Meso-Inhomogeneous Deformation on a Metal Material Surface under Low-Cycle Fatigue

Crystallographic Study of Surface Finish in Pack Rolling of Thin Sheets

Inhomogeneous Deformation Growth of a Metal under Cyclic Loading and Its Influence on Fatigue

Anisotropy of Yielding/Hardening and Micro-Inhomogeneity of Deforming/Rotating for A Polycrystalline Metal under Cyclic Tension Compression

Micro-failure of metals under inhomogeneous plastic deformation

The effects of surface-layer grain size and texture on deformation-induced surface roughening in polycrystalline titanium hardened by ultrasonic impact treatment