Abstract:The purpose of this study is to quantitatively analyze the effect of strain path on roughness evolution of free surface during plastic deformation. Firstly, the crystal plastic finite element model for a representative volume element (RVE) of polycrystalline is established, including the polycrystalline geometric model and initial topography model. Next, based on two groups of strain path including five typical strain paths, i.e., uniaxial tension (UT), biaxial tension (BT), plane strain tension (PST), plane strain compression (PSC) and in-plane pure shear (PPS), the 3D surface roughness of free surface after the plastic deformation is presented quantitatively. The total change of surface topography can be divided into two parts, which relate to the homogenous deformation and inhomogeneous deformation. In a simple manner, the homogenous deformation and inhomogeneous deformation can correspond with the elastic deformation and plastic deformation respectively. As in the elastic deformation, the effect of the misorientation of the adjacent grains and strain localization in the polycrystalline material on the surface topography has no chance to exert on the very small strain. So the inhomogeneity of polycrystalline material has been ignored in the elastic deformation. For the effect of homogeneous deformation, the relationship between the surface roughness of the deformed surface, initial roughness and strain path is analytically derived. For the contribution of the inhomogeneous deformation to surface roughening, the quantitative relationship between surface roughness of the deformed surface and the strain path is acquired by the mathematical fitting based on hundreds of crystal plasticity finite element simulations. The final surface roughness of the deformed surface is obtained by combining these two parts. Then the experiment of biaxial tension on 6061 aluminum alloy sheet is taken as an example to verify the accuracy of surface roughness calculation. The comparison of experimental results and calculated results shows good consistency. Thereafter the surface roughening phenomena in the plastic deformation are observed at three different scales. The homogeneous deformation does not form additional peaks and valleys but changes the spacing and height of peaks and valleys of the initial surface topography, which brings about the surface roughening at macroscale level. In inhomogeneous deformation, the misorientation of the adjacent grains in the polycrystalline material is taken into consideration, which leads to the grain rotation and generates the additional peaks and valleys of the initial surface topography. The surface roughening due to this part can be seen at the mesoscopic scale. And the step phenomenon caused by slip bands inner the grains is the microscopic scale roughening behavior. This work is beneficial to understand the roughness evolution of free surface quantitatively with the effect of strain path and make out the surface roughening phenomena at different scales.

On the evolution of surface roughness during deformation of polycrystalline aluminum alloys

Deformation-Induced Surface Roughening of an Aluminum–Magnesium Alloy: Experimental Characterization and Crystal Plasticity Modeling

Surface Roughness Evolution under Constant Amplitude Fatigue Loading Using Crystal Plasticity

Surface Roughening Behavior of the 6063-T4 Aluminum Alloy During Quasi-in Situ Uniaxial Stretching

Surface Roughening Behavior and Mechanism in Aluminum Alloy Under Tensile Deformation

Analysis of surface roughening behavior of 6063 aluminum alloy by tensile testing of a trapezoidal uniaxial specimen

Effect of Strain Path on Roughness Evolution of Free Surface During Plastic Deformation

In-situ EBSD Study of the Active Slip Systems and Lattice Rotation Behavior of Surface Grains in Aluminum Alloy During Tensile Deformation

Effect of Strain State on the Surface Roughening for Hydroforming of Aluminum Alloy Tube Based on Cross-Scale Numerical Modeling

Finite Element Simulation of Surface Deformation of Polycrystal with a Rough Surface under Repeated Load

The universal emergence of self-affine roughness from deformation

Quantitative Analysis of Surface Roughness Evolution in FCC Polycrystalline Metal During Uniaxial Tension

Crystal Plasticity Finite Element Simulation of Grain Evolution Behavior in Aluminum Alloy Rolling

Experimental and Numerical Investigation of Mesoscale Deformation-Induced Surface Roughening in Polycrystalline Metals and Alloys (Review)

Nonequilibrium plastic roughening of metallic glasses yields self-affine topographies with strain-rate and temperature-dependent scaling exponents

Research Status of Surface Roughening during Plastic Deformation

Mechanism of the effect of plastic deformation at different temperatures on the surface roughness of machined aluminum mirrors

Microstructure and flow stress of polycrystals and single crystals

Investigation of Yield Surfaces Evolution for Polycrystalline Aluminum after Pre-Cyclic Loading by Experiment and Crystal Plasticity Simulation

Grain orientation dependence of microstructure in aluminium deformed in tension

Strain Distribution and Lattice Rotations During In-Situ Tension of Aluminum with a Transmodal Grain Structure