Abstract:Enhancing inlet gas temperature in aero/gas turbines to reduce their carbon-footprint, has led to a strive for better performing inlet cooling mechanism of the turbine blades. The internal cooling of the blades is made by ceramic cores in their casting process, but conventional ceramic molding has long reached its maximum possible geometrical complexity, hence shedding light on 3D printing of these cores. The objective of this study is to develop low-viscous, fully stabilized, commercially viable ink for vat-photopolymerization of silica-based ceramics. This paper investigates the best dispersion type and amount for different formulated monomer mixtures, and explains the best correlation between viscosity, solid loading, binders, dispersants, peeling forces and mechanical properties, and offers an optimized mixture to avoid the common ceramic printing issue, namely crack propagation of cores during sintering. Among five dispersant agents, the SOL20, SOL24 and FA4611 exhibited better performance than other dispersion agents, and the optimum concentration level for each binder and dispersant agent was ensured through sedimentation test. Their dispersion capability and long-term stability were further investigated to designate the best dispersion agent for each binder system. Further verification was made by sedimentation study of the samples at 40 °C for 40 days and reducing the superficial area of the used powder mixture. According to the result of the rheology analysis, the best dispersions were achieved using SOL20 for the loaded binder mixtures of M1 and M4, SOL24 for M3and FA4611 for M2. The instability of M1 and M2 with their respective dispersant agent was coordinated through the thixotropic agent of TX/2, and complete stabilization and near-Newtonian behavior were achieved. However, the research showed that the addition of TX/2 to fully stabilized M4 and M2 suspensions negatively impacts the mixtures' rheological behavior from near-Newtonian to shear-thickening. In the final stage of this study, peeling forces, sintering and three-point bending tests were conducted to determine the final formulated suspension to print ceramic core components. M4 and SOL20 combination was selected for SiO 2 -ZrSiO 4 loading and dispersing, respectively. The impact of solid loading between the range of 58 and 65 vol.% on the rheological behavior of the final suspension and the mechanical properties of sintered bodies were investigated to assign an optimum solid rate. The adequate strength on sintered and degree of viscosity for ceramic vat-polymerization processing was achieved at 58 vol.%. Lastly, a validation study is conducted by printing a complex ceramic core model by a commercial LCD hobby printer. This validation shows the significance of this study to scale up the manufacturing of complex-shaped ceramic cores and to revolutionize the sector, by printing inexpensive and readily available irregular-shaped (non-atomized) ceramic powder, using the most cost-effective LCD printers (non-specialized expensive ceramic printers).

Dissipative Particle Dynamics of Nano-Alumina Agglomeration in UV-Curable Inks

Inter-particle interactions of alumina powders in UV-curable suspensions for DLP stereolithography and its effect on rheology, solid loading, and self-leveling behavior

Optimization of 3D Printing Parameters for Alumina Ceramic Based on the Orthogonal Test

Study of alumina ceramic parts fabricated via DLP stereolithography using powders with different sizes and morphologies

Relationship between the adhesion properties of UV-curable alumina suspensions and the functionalities and structures of UV-curable acrylate monomers for DLP-based ceramic stereolithography

Optimization of the sintering thermal treatment and the ceramic ink used in direct ink writing of α-Al2O3: Characterization and catalytic application

Development and Characterizations of Novel Aqueous-Based Ceramic Inks for Inkjet Printing

Recent progress of alumina ceramics by direct ink writing: Ink design, printing and post-processing

Agglomeration behavior of carbon-supported platinum nanoparticles in catalyst ink: modeling and experimental investigation

Direct Ink Writing of Tubular Al2O3 Membrane Support Using Agar-Based Ink in 3D-Printing

The Role of Liquid Ink Transport in the Direct Placement of Quantum Dot Emitters Onto Sub-Micrometer Antennas by Dip-Pen Nanolithography.

Influence of resin composition on rheology and polymerization kinetics of alumina ceramic suspensions for digital light processing (DLP) additive manufacturing

Embedded Direct Ink Writing 3D Printing of UV Curable Resin/Sepiolite Composites with Nano Orientation

A novel experimental approach to quantitatively evaluate the printability of inks in 3D printing using two criteria

Preparation and characterization of waterborne ceramic ink with submicron-sized praseodymium-doped zirconium silicate pigment by water-based diblock polymer dispersants

Effect of particle size distribution and printing parameters on alumina ceramics prepared by Additive Manufacturing

Influence of several binders on the mechanical properties of alumina parts manufactured by 3D inkjet printing

3D gel printing of alumina ceramics followed by efficient multi-step liquid desiccant drying

Binder stabilization and rheology optimization for vat-photopolymerization 3D printing of silica-based ceramic mixtures

Additive manufacturing solidification methodologies for ink formulation

Reinforcement effect in printing precision and sintering performance for liquid crystal display stereolithography additive manufacturing of alumina ceramics