Abstract:Tungsten carbide (WC), celebrated for its exceptional strength, hardness, and chemical inertness, serves as an exemplary reinforcement for copper (Cu) matrix composite (CMC) coatings, significantly enhancing their wear and corrosion resistance. However, the inherent poor wettability and interfacial bonding between WC and Cu during the cold spray additive manufacturing process pose challenges to further performance improvement of these coatings. This study investigates cold-sprayed CMC coatings reinforced with WC particles, both with and without an electroless plated cobalt (Co) shell (Co@WC; at 10 wt.% and 20 wt.%), focusing on their microstructure, mechanical properties, tribological behavior, and electrochemical corrosion resistance. The findings indicate a reduction in CMC coatings` porosity and mean free path (MFP) of reinforcement particles with increasing reinforcement content. Despite slight Co shell damage during deposition, ceramic retention is notably enhanced, reaching up to 149.3%. The microhardness and wear resistance of CMC coating are improved with decreased MFP and increased ceramic content. Compared to the Cu coating, the microhardness of CMC coatings escalates by up to 32.9% (151.8HV0.1), and the specific wear rate is dramatically reduced by up to 84.2%. The Co shell effectively prevents the detachment of Co@WC particles, thereby enhancing the bending and wear resistance. Electrochemical corrosion tests, encompassing open circuit potential (EOCP), polarization curve, and electrochemical impedance spectroscopy (EIS), indicate that lower porosity, high ceramic content and the Co shell substantially boost the corrosion resistance of the CMC coating. Specifically, the coating with 20 wt.% Co@WC (Cu20(Co@WC)) demonstrates superior corrosion resistance compared to the Cu coating, hinting at the potential for further enhancement with increased ceramic content.

Study on the electrical properties of Cu-based ECMs prepared by TiBN powder instead of W

Microstructure and Properties of In-Situ TiC Reinforced Copper Nanocomposites Fabricated Via Long-Term Ball Milling and Hot Pressing

Enhanced the Mechanical Properties and Corrosion Resistance of Ultra-Coarse Grain WC-8Co Cemented Carbides by the Introduction of Cu and Ni

Effect of TiB2 on properties and microstructures of Cu W electrical contact materials

Tribological and Electrochemical Corrosion Behaviors of Cu-based Powder Metallurgy Composites Reinforced by In-Situ WC with Different Morphology

Cold-sprayed Cu Matrix Composite Coatings with Core-Shell Structured Co@WC Reinforcements on Q235 Steel

High-temperature mechanical and electrical properties of W-particle-reinforced Cu-matrix composites from improved electroless plated powders

Effect of Cu Content on the Precipitation Behaviors, Mechanical and Corrosion Properties of As-Cast Ti-Cu Alloys

Designed bimetallic layer-encapsulated tungsten powders for reinforcing tungsten-silver matrix composite electrical contact materials

Influence of TiC Content on Microstructure and Properties of W-3OCu/TiC Composites

The Influence of TiB2 Content on Microstructure and Properties of W–30Cu Composites Prepared by Electroless Plating and Powder Metallurgy

Microstructure, Mechanical and Tribological Properties of Cu40Zn-Ti3AlC2 Composites by Powder Metallurgy

Study on the arc erosion resistance and mechanism of Cr- doped W Cu composites

Enhancing Mechanisms of Arc-Erosion Resistance for Copper Tungsten Electrical Contact Using Reduced Graphene Oxides in Situ Modified by Copper Nanoparticles

Improving comprehensive performance of copper matrix composite by spray pyrolysis fabricated CNT/W reinforcement

Microstructure and Mechanical Properties of Cu Matrix Composites Reinforced by TiB2/TiN Ceramic Reinforcements

Influence of TiC Content on Microstructure and Properties of W-30Cu/TIC Composites

Microstructures and properties of in situ (TiB 2p +TiB w )/Cu composites with different Ce content

Fabrication and characterization of W/Cu/Ni-based high specific gravity alloy with Zr and Ti combined addition

Study on Microstructure and Mechanical Properties Modification of Cu-Ti3AlC2 Composites by Ni Element

Comparative study of the microstructure and arc erosion resistance of Ag/Ti 2 AlX (X=C, N) electrical contact materials