Abstract:W70Cu30(W-30 wt.% Cu) alloys were fabricated using cold pressing and infiltration sintering methods from two types of powders, i.e., mixed copper-tungsten (M-Cu-W) powders and our newly developed copper-coated tungsten composite (Cu@W) powders. Microstructure, mechanical and arc-ablation properties of the W70Cu30 alloys were investigated, and the mechanism of enhanced physical/mechanical properties and arc-erosion resistance of the W70Cu30 alloys was discussed. For the W70Cu30 alloys prepared using the Cu@W powders, their physical properties, including hardness, electrical conductivity and relative density were much better than those prepared from the M-Cu-W powders. The W70Cu30 alloys fabricated from the Cu@W powders were free of cracks, and showed homogenous distributions of W and Cu network structures. Whereas for the alloys prepared from the M-Cu-W powders, segregation of Cu was observed and the segregation size was about 40-100 mm. Characterization of arc-erosion morphologies of the W70Cu30 alloys prepared with the Cu@W powders revealed the occurrence of evaporation of Cu phase; whereas that of W70Cu30 alloys prepared with the M-Cu-W powders revealed the occurrence of the sputtering of Cu. After arc breakdown for 200 times, mass loss of alloys made using the mixed powders was twice as much as those made using the coated composite powders. Based on the experimental results and theoretical analysis, an arc breakdown mechanism of the WCu-C alloys using the composite powders was proposed which is attributed to the formation of a homogeneous Cu-Cu network structure to uniformly disperse arc energy and dissipate the generated heat, thus prolonging the service life of the WCu alloy contacts. (c) 2017 Elsevier B.V. All rights reserved.

Study on the arc erosion resistance and mechanism of Cr- doped W Cu composites

Influences of Ni/Cu/Cr3C2 Composite Additive on Microstructure and Properties of WC–10Co Fine Grained Hardmetal

Arc erosion resistance of WC/CuCr30 composites based on changing of Cr particle morphology and orientation

Cr Effects on the Electrical Contact Properties of the Al2O3-Cu/15W Composites

Vacuum Arc Motion Characteristics on CuWCr Composites

Microstructure and electrical contact behavior of the nano-yttria-modified Cu-Al2O3/30Mo/3SiC composite

Infiltration Sintering of WCu Alloys from Copper-Coated Tungsten Composite Powders for Superior Mechanical Properties and Arc-Ablation Resistance

Vacuum Breakdown Behavior of CuWCr Composites

Microstructure, mechanical properties and arc erosion behavior of CuW composites prepared by high energy ball milling and spark plasma sintering

Wear-resistance enhancement of nanostructured W-Cu-Cr composites

Study on Arc Ablative Properties of W-Cu Composites at Different Voltages

Influence of WC particles addition on material transfer behavior of CuCr30 contact material

Preparation and Arc Erosion Resistance of Cf/Cu Composite by Vacuum Melting Infiltration

Understanding wetting mechanism of pure Cu on C/C composites modified by chromium carbide

Enhancing Mechanisms of Arc-Erosion Resistance for Copper Tungsten Electrical Contact Using Reduced Graphene Oxides in Situ Modified by Copper Nanoparticles

Arc Erosion Behavior of a Nanocomposite W-Cu Electrical Contact Material

Preparation and Arc Breakdown Behavior of Nanocrystalline W-Cu Electrical Contact Materials

Enhanced arc erosion resistance via constructing W particle network structure in cold sprayed CuCrZr–W coating: Implication for electromagnetic launching system

Microstructure and properties of W Cu composites reinforced by in-situ generated WC

Influence Of Cr Particle Size On The Microstructure And Electrical Properties Of Cuw60cr15 Composites

Excellent wear resistance of multicomponent nanocrystalline W‒Cu based composite