Abstract:Polycarbonate (PC) and protective (Ti,Al)N coatings exhibit extremely different material properties, specifically crystal structure, thermal stability, elastic and plastic behavior as well as thermal expansion coefficients. These differences present formidable challenges for the deposition process development as low-temperature synthesis routes have to be explored to avoid a thermal overload of the polymer substrate. Here, a large-area sputtering process is developed to address the challenges by systematically adjusting target peak power density and duty cycle. Adhering (Ti,Al)N coatings with a critical residual tensile stress of 2.2 +/- 0.2 GPa are obtained in the pulsed direct current magnetron sputtering range, whereas depositions at higher target peak power densities, realized by high power pulsed magnetron sputtering, lead to stress-induced adhesive and/or cohesive failure. The stress-optimized (Ti,Al)N coatings deposited onto PC with a target peak power density of 0.036 kW cm-2 and a duty cycle of 5.3% were investigated by cross-cut test confirming adhesion. By investigating the bond formation at the PC | (Ti,Al)N interface, mostly interfacial CNx bonds and a small fraction of (C-O)-(Ti,Al) bonds are identified by X-ray photoelectron spectroscopy, indicating reactions at the hydrocarbon and the carbonate groups during deposition. Nanoindentation reveals an elastic modulus of 296 +/- 18 GPa for the (Ti,Al)N coating, while a Ti-Al-O layer is formed during electrochemical impedance spectroscopy in a borate buffer solution, indicating protective passivation. This work demonstrates that the challenge posed by the extremely different material properties at the interface of soft polymer substrates and hard coatings can be addressed by systematical variation of the pulsing parameters to reduce the residual film stress.

A Study of the Influence of Process Parameters of AP PECVD on the Mechanical Properties of Silica-like Films Deposited on Polycarbonate

The Effect of the Process Parameters on the Growth Rate and Composition of the Anti Scratch Films Deposited from TEOS by AP-PECVD on Polycarbonate

Stabilizing the Wettability of Initiated Chemical Vapor Deposited (icvd) Polydivinylbenzene Thin Films by Thermal Annealing

SEM Research of SiO2 Thin Film on Inner Wall of Glass Container by PECVD

Abrasion Resistance and Transmittance of DLC Films Deposited on PC Resin

CATHODICALLY ELECTROCHEMICAL-ASSISTED DEPOSITION AND PROTECTIVE PROPERTIES OF SILANE FILMS

Embedding constructed refractive index graded antireflective coating with high abrasion resistance and environmental stability for polycarbonate glass

Improvement of water and gas barrier properties of polycarbonate by the SiO x plasma treatment

Large-area deposition of protective (Ti,Al)N coatings onto polycarbonate

Characterization of High Rate Deposited PECVD Silicon Dioxide Films for MCM Applications

Decorative Chromium Coatings on Polycarbonate Substrate for the Automotive Industry

Treatment of PDMS surfaces using pulsed DBD plasmas: comparing the use of different gases and its influence on adhesion

Feasibility of molecular dynamics simulation for process parameter guidance of silicon nitride thin films by PECVD

Surface Roughness Effects on the Properties of Silicon-Doped Diamond-like Carbon Coatings

Joining and Coating of Plasma Electrolytic Oxidated Aluminum Using a Silica Preceramic Polymer

Transparency, Wettability, and Tribological Properties of Amorphous Hydrogenated Carbon Films Deposited on PMMA by RF-PECVD

Mechanical and Surface Characterization of Diamond-Like Carbon Coatings onto Polymeric Substrate

Morphologic and Chemical Properties of PMMA/ATH Layers with Enhanced Abrasion Resistance Realised by Cold Plasma Spraying at Atmospheric Pressure

Preparation, wear resistance, and impact toughness of homoepitaxial diamond film deposited on polycrystalline diamond compact by HFCVD method

Ultra-thin Parylene-C Deposition on PDMS

In-situ growing amorphous carbon film with attractive mechanical and tribological adaptability on PEEK via continuous plasma-induced process