Abstract:The use of ultra-fine dredged sand instead of natural sand in construction 3D printing materials can significantly reduce the cost. However, ultra-fine dredged sand has fine particles and high angular morphology, which can hinder the buildability and continuous printability of construction 3D printing materials. The addition of polycarboxylate superplasticizer (PCE) can effectively solve this problem. Considering that the change of PCE (content of 0, 0.1%, 0.2%, 0.3%) content has a great influence on the printing performance of mortar, in order to make up for this deficiency, nano clay (content of 0,1%) is added to the mortar. The experimental results showed that the addition of nano clay can significantly reduce the negative effects of PCE on the yield stress and apparent viscosity of 3D printing materials (3DPM). When the content of PCE is 0.2%, the addition of 1% NAC could increase the static yield stress and viscosity growth rate of 3DPM by 111.8% and 115.3% respectively. In addition, unconfined compressive strength test, isothermal calorimetry, mercury invasion porosity method and thermogravimetric analysis were used to characterize the hardening properties of 3DPM. The results of heat of hydration showed that the addition of nano clay reduced the hydration exothermic peak of 3DPM, but increased the total heat release. The results of pore structure analysis showed that the addition of nano clay reduced the macropore (>1000 nm) of 3DPM from 19.31% to 18.82%. Thermogravimetric analysis showed that the addition of nano clay increased the hydration products. Therefore, the compressive strength of 3DPM was kept within an acceptable range. Finally, the laboratory's printing results indicated that the 3DPM can print up to 20 layers continuously.

Mix Design and 3D Printing Correlation Performance of Pcc-Based 3DPM

Effects of additives on the mechanical properties, rheology, and printing properties of Pcc-based 3DPMs

Study of 3D printed concrete with low-carbon cementitious materials based on its rheological properties and mechanical performances

The relationship between the rheological behavior and interlayer bonding properties of 3D printing cementitious materials with the addition of attapulgite

A novel method for improving the printability of cement-based materials: Controlling the releasing of capsules containing chemical admixtures

Mechanical Performance of Commercially Available Premix UHPC-Based 3D Printable Concrete

Cementitious composites blending with high belite sulfoaluminate and medium-heat Portland cements for largescale 3D printing

A review of 3D printed concrete: Performance requirements, testing measurements and mix design

Strength and Proportioning Design of 3D Printed Concrete (3DPC) Based on Aggregate Gradation Optimization

WFT-based assessment of the rheological characteristics, particle packing, and buildability of Pcc-FA-GGBFS composite materials for 3D printing

D-optimal design of experiments applied to 3D high-performance concrete printing mix design

Inclined 3D concrete printing: build-up prediction and early-age performance optimization

Effect of nano clay and PCE on the buildability of ultra-fine dredged sand-based 3D printing materials

Properties and Microstructures of 3D Printable Sulphoaluminate Cement Concrete Containing Industrial By-Products and Nano Clay

Comparative Evaluation of the Applicability of 3D Printing Mortar with Different Waste Powders

Preliminary Study of the Fresh and Hard Properties of UHPC That Is Used to Produce 3D Printed Mortar

A new strategy to enhance 3D printability of cement-based materials: In-situ polymerization

3D Printing of Fiber-Reinforced Calcined Clay-Limestone-Based Cementitious Materials: From Mixture Design to Printability Evaluation

A rheological-based printability assessment method for 3D printing Engineered Cementitious Composites considering fiber dispersion

3D printing of calcined clay-limestone-based cementitious materials

Improving printability of limestone-calcined clay-based cementitious materials by using viscosity-modifying admixture