Abstract:As we know, 3DPC is printed layer by layer compared with mold-casting conventional concrete. Pore structure and layer-to-layer interface are two main aspects of the internal structure for 3DPC, which decide 3DPC's mechanical performance. The layer-to-layer interface caused by printing is specific to 3DPC. The emphasis of this study lies in the layer-to-layer interfaces of 3DPC. The first aim of this study is to quantify the characteristics of the layer-to-layer interface and therefore characterize different aspects of the interfaces. The second aim of this study is to explore how the internal structure of printed concrete influences the mechanical performance of 3DPC. This research set out to design a series of experimental comparisons between 3DPC and casted concrete with the same compositions. Mechanical tests, i.e., compressive stress, ultrasonic Pulse Velocity test, flexural tension, and tension splitting, as well as the Ultrasonic Pulse Velocity test, were performed to check the mechanical performance of 3DPC. Contrary to what has often been expected, the mechanical test results showed the printed concrete has a quality not worse than casted concrete with the same recipe. Meanwhile, the X-ray computed tomography (X-CT) is used to characterize the internal structure, pore shapes, and interfaces of 3DPC. First, the investigation revealed that the lower total porosity and fewer big voids could be the fundamental causes meaning 3DPC has a better mechanical performance than casted concrete. Second, the statistics based on aspect ratio show that the distribution curves follow similar trends, regardless of the printed or casted concrete. Third, this study quantified the depth of the different interfaces for 3DPC. The results suggest that the porosity in an interface varies in a range. The author's pioneer work has contributed to our present understanding of the interfaces of 3DPC.

The relationship between the rheological behavior and interlayer bonding properties of 3D printing cementitious materials with the addition of attapulgite

Investigation of the Internal Structure of Hardened 3D-Printed Concrete by X-CT Scanning and Its Influence on the Mechanical Performance.

Bond shear performances and constitutive model of interfaces between vertical and horizontal filaments of 3D printed concrete

Interlayer bonding investigation of 3D printing cementitious materials with fluidity retaining polycarboxylate superplasticizer and high dispersion polycarboxylate superplasticizer

A novel method for improving the printability of cement-based materials: Controlling the releasing of capsules containing chemical admixtures

3D printing concrete with recycled coarse aggregates: The influence of pore structure on interlayer adhesion

Strength and Proportioning Design of 3D Printed Concrete (3DPC) Based on Aggregate Gradation Optimization

Mechanical properties, durability performance and interlayer adhesion of 3DPC mixtures: A state‐of‐the‐art review

Study of 3D printed concrete with low-carbon cementitious materials based on its rheological properties and mechanical performances

Effects of additives on the mechanical properties, rheology, and printing properties of Pcc-based 3DPMs

Effects of bentonite, diatomite and metakaolin on the rheological behavior of 3D printed magnesium potassium phosphate cement composites

3D printing concrete technology from a rheology perspective: a review

Mix Design and 3D Printing Correlation Performance of Pcc-Based 3DPM

PVA Fibre Reinforced High-Strength Cementitious Composite for 3D Printing: Mechanical Properties and Durability

Improving printability of limestone-calcined clay-based cementitious materials by using viscosity-modifying admixture

Yield stress and thixotropy control of 3D-printed calcium sulfoaluminate cement composites with metakaolin related to structural build-up

A review of 3D printed concrete: Performance requirements, testing measurements and mix design

Modification effect of nanosilica and polypropylene fiber for extrusion-based 3D printing concrete: Printability and mechanical anisotropy

Influence of pore defects on the hardened properties of 3D printed concrete with coarse aggregate

Effect of Nanostructured Silica Additives on the Extrusion-Based 3D Concrete Printing Application

3D Printing of Fiber-Reinforced Calcined Clay-Limestone-Based Cementitious Materials: From Mixture Design to Printability Evaluation