Abstract:Although the use of 3D printing in civil engineering has grown in popularity, one of the primary challenges associated with it is the absence of steel bars inside the printed mortar. As a result, developing 3D printing mortar with ultra-high compressive, flexural, and tensile strengths is critical. In the present study, an ultra-high-performance mortar incorporating silica fume (SF) and graphene nanoplatelets (GNPs) was developed for 3D printing application. The concrete mixture added SF to the concrete mixture in the range between 0% and 20%, while GNPs were added as a partial replacement by cement weight from 0.5% to 2%. The flowability and the machinal properties of the proposed mortar, including compressive (CS), tensile (TS), and flexural strength (FS), were investigated and assessed. Microstructure analysis involving FESEM and EDX was also investigated and evaluated, while response surface methodology (RSM) was considered to predict and optimize the optimum value of GNPs and SF. Workability results show that the flowability is reduced when the amount of graphene increases. Based on the predicted and experimental results, ultra-high-strength mortar can be developed by including 1.5% of GNPs and 20% of SF, in which the CS jumped from 70.7 MPa to 133.3 MPa at the age of 28 days. The FS and TS were 20.66 MPa and 14.67 MPa compared to the control mix (9.75 MPa and 6.36 MPa), respectively. This favorable outcome was credited to the pozzolanic activity of SF and the effectiveness of GNPs in compacting the pores and bridging the cracks at the nanoscale level, which were verified by FE-SEM and EDX. In addition, the developed quadratic equations proved their accuracy in predicting and optimizing the mechanical properties with low error (less than 0.09) and high correlation (R2 > 0.97). It can be concluded that the current work is an important step forward in developing a 3D printing mortar. The lack of reinforcement in the printed mortar structure has been a considerable difficulty, and the SF and GNPs have increased the compressive, flexural, and tensile strengths of the mortar. Thus, these improvements will encourage the industry to utilize sustainable materials to produce more affordable housing.

Modification effect of nanosilica and polypropylene fiber for extrusion-based 3D printing concrete: Printability and mechanical anisotropy

Effect of Nanostructured Silica Additives on the Extrusion-Based 3D Concrete Printing Application

Properties and Microstructures of 3D Printable Sulphoaluminate Cement Concrete Containing Industrial By-Products and Nano Clay

A new strategy to enhance 3D printability of cement-based materials: In-situ polymerization

PVA Fibre Reinforced High-Strength Cementitious Composite for 3D Printing: Mechanical Properties and Durability

A novel method for improving the printability of cement-based materials: Controlling the releasing of capsules containing chemical admixtures

Study of 3D printed concrete with low-carbon cementitious materials based on its rheological properties and mechanical performances

Effect of nano clay and PCE on the buildability of ultra-fine dredged sand-based 3D printing materials

Mechanical Properties and Pore Structure of Multiwalled Carbon Nanotube-Reinforced Reactive Powder Concrete for Three-Dimensional Printing Manufactured by Material Extrusion.

Micro/Nano additives in 3D printing concrete: Opportunities, challenges, and potential outlook in construction applications

Influence of Multi-Walled Nanotubes on the Fresh and Hardened Properties of a 3D Printing PVA Mortar Ink

Rheological behaviors and structure build-up of 3D printed polypropylene and polyvinyl alcohol fiber-reinforced calcium sulphoaluminate cement composites

Investigation of the material mixtures and fiber addition for 3D concrete printing

Influence of pore defects on the hardened properties of 3D printed concrete with coarse aggregate

An Overview on the Rheology, Mechanical Properties, Durability, 3D Printing, and Microstructural Performance of Nanomaterials in Cementitious Composites

Mechanical performance and anisotropic analysis of rubberised 3D-printed concrete incorporating PP fibre

Research on Mechanical Properties of a 3D Concrete Printing Component-Optimized Path by Multimodal Analysis

Improving mechanical properties of 3D printed mortar by exploiting synergistic effects of fly ash microsphere and nano-silica

Development of Ultra-High-Performance Silica Fume-Based Mortar Incorporating Graphene Nanoplatelets for 3-Dimensional Concrete Printing Application

Shrinkage and mechanical properties optimization of spray-based 3D printed concrete by PVA fiber

Rheological characterization of ultra-high performance concrete for 3D printing