Abstract:Three-dimensional (3D) printing has been increasingly applied to experimental research in geotechnical engineering. In this paper, standard cylinder specimens with high and low strength were prepared using 3D-printing sand core technology. The elastic-plastic and rheological mechanical behaviors were experimentally studied. In addition, the similarity and limitations were verified through comparison with natural sandstone, slate, sand-gypsum, claystone, etc. On this basis, a new way to prepare soft-hard interbedded layered rock in geotechnical mechanics was developed. Considering the features of layered rock and the principle of 3D printing, cylindrical and cubic specimens of soft-hard interlayered rock mass with different inclination angles were prepared by controlling the binder content layer by layer. The deformation and strain differences between the soft and hard phases were verified through digital image correlation. In this case, the anisotropic failure evolution mode of soft-hard interbedded rock mass was revealed by the images captured. The structural anisotropy behaviors of 3D-printed soft-hard interbedded rock was also studied. The results agree well with the published experimental and theoretical results. This study introduces a broad prospect of 3D printing sand core technology for future experimental mechanical research on a soft-hard interbedded layered rock mass in geotechnical engineering. This study developed a new method for preparing soft-hard interbedded rock masses based on 3D printing sand core technology. The elastic-plastic and rheological characteristics of 3D-printed soft rock, hard rock, and soft-hard interbedded rock were investigated and compared with a natural layered rock mass. Moreover, the deformation and strain differences between the soft and hard phases were verified from a mesoscopic perspective. The structural anisotropy behaviors and anisotropic failure mode of soft-hard interbedded rock mass were revealed. The results agreed well with the published experimental and theoretical results. Thus, specimens with complex structures, such as soft-hard interbedded rock mass, could be prepared with 3D printing sand core technology. As a result, the mechanical parameters of 3D-printed specimens were close to those of sandy mudstone and claystone rock masses, while the trends of the stress-strain curves of 3D-printed specimens were consistent with natural sandstone rock masses. This study brings a broad prospect for future investigation of the soft-hard interbedded layered rock mass in actual geotechnical engineering.

Influence of pore defects on the hardened properties of 3D printed concrete with coarse aggregate

Investigation of the Internal Structure of Hardened 3D-Printed Concrete by X-CT Scanning and Its Influence on the Mechanical Performance.

Bond shear performances and constitutive model of interfaces between vertical and horizontal filaments of 3D printed concrete

Hardened properties of 3D printed concrete with recycled coarse aggregate

3D printing concrete with recycled coarse aggregates: The influence of pore structure on interlayer adhesion

Mechanical and macrostructural properties of 3D printed concrete dosed with steel fibers under different loading direction

PVA Fibre Reinforced High-Strength Cementitious Composite for 3D Printing: Mechanical Properties and Durability

Strength and Proportioning Design of 3D Printed Concrete (3DPC) Based on Aggregate Gradation Optimization

Modification effect of nanosilica and polypropylene fiber for extrusion-based 3D printing concrete: Printability and mechanical anisotropy

Bonding properties between 3D printed coarse aggregate concrete and rebar based on interface structural characteristics

Hardened properties of 3D printed concrete: The influence of process parameters on interlayer adhesion

Interfacial bonding properties of 3D printed permanent formwork with the post-casted concrete

Unveiling pore formation and its influence on micromechanical property and stress distribution of 3D printed foam concrete modified with hydroxypropyl methylcellulose and silica fume

Investigation of 3D Printing Sand Core Technology on the Mechanical Behaviors of Soft–Hard Interbedded Rock Masses

Mechanism of the influence of multi-scale pore structure on the triaxial mechanical properties of 3D printed concrete with recycled sand

Comprehensive investigations on the relationship between the 3D concrete printing failure criterion and properties of fresh-state cementitious materials

The relationship between the rheological behavior and interlayer bonding properties of 3D printing cementitious materials with the addition of attapulgite

Triaxial compressive behavior of 3D printed PE fiber-reinforced ultra-high performance concrete

Study on anisotropy of 3D printing PVA fiber reinforced concrete using destructive and non-destructive testing methods

Interfacial Properties of Three-Dimensional-Printed Permanent Formwork with Cast-in-Place Concrete

3D printed concrete with recycled sand: Pore structures and triaxial compression properties