Abstract:Heterostructured high-entropy alloys (HEAs) exhibit a good combination of strength and ductility. However, the deformation mechanisms and related mechanical properties of the heterogeneous nanostructured body-centred cubic (BCC) HEAs remain largely unrevealed. Here, we report the effect of the strain rate on the mechanical properties and microstructural evolution in the heterostructured Al3CoCrCuFeNi HEA with the gradient grain size ranging from 9 nm at the surface to 45 nm in the center using the large-scale atomic simulations. Based on the characterization of microstructure evolution from the atomic simulation, a microstructure-based constitutive model that utilizes a single parameter set is established to study the effects of the multiple strengthening mechanisms at different stages on the strength and strain hardening of the heterostructured HEA under different strain rates. The results show that the plastic deformation mechanisms are strongly influenced by the strain rate in the range of 1 × 106 to 1 × 1010 s−1. The dislocation and deformation twin are the main deformation mechanisms at the strain rate less than 1 × 108 s−1. The deformation twinning cooperated with multiple phase transformations plays a pivotal role at the strain rate of 1 × 109 s−1. The multiple phase transformations are the dominant plastic deformation model at the strain rate of 1 × 1010 s−1, which is different from the classic plastic-deformation mode, including the dislocation and deformation twin in traditional alloys. This phenomenon is ascribed to various types of atomic interactions and atomic-size mismatches, which produce strong lattice distortion. In particular, a large number of edge dislocations are observed, which is extremely different from screw dislocations invariably generated in traditional BCC alloys, and thus, could be responsible for high strength. Furthermore, the stress-strain response of the Al3CoCrCuFeNi HEA is derived from the individual contributions of the lattice distortion, dislocation, grain boundary, deformation twin, phase transformation, and back-stress strengthening mechanisms. The heterogeneous grain boundaries and lattice distortion contribute the most to the yield strength, and the dislocation, deformation twin, phase transformation, and back stress dominate the strain hardening. Therefore, these results highlight a new design strategy of HEAs to tailor their mechanical properties based on the partition of the multistage strengthening mechanisms by the heterostructure.

Hetero-deformation-induced (HDI) plasticity induces simultaneous increase in both yield strength and ductility in a Fe 50 Mn 30 Co 10 Cr 10 high-entropy alloy

Ultrahigh Cryogenic Strength and Exceptional Ductility in Ultrafine-Grained CoCrFeMnNi High-Entropy Alloy with Fully Recrystallized Structure

Heterostructuring an equiatomic CoNiFe medium-entropy alloy for enhanced yield strength and ductility synergy

Inherent and Multiple Strain Hardening Imparting Synergistic Ultrahigh Strength and Ductility in a Low Stacking Faulted Heterogeneous High-Entropy Alloy

Recrystallized hard zone and resultant tri-modal microstructure produces superior mechanical properties in a single-phase heterostructured high-entropy alloy

Strain partitioning enables excellent tensile ductility in precipitated heterogeneous high-entropy alloys with gigapascal yield strength

Dislocation array reflection enhances strain hardening of a dual-phase heterostructured high-entropy alloy

A new strategy to overcome the strength-ductility trade off of high entropy alloy

Heterogeneous Microstructure and Tensile Properties of Fe50Mn30Co10Cr10 Metastable High-Entropy Alloy

Plasticity Improvement in a Co-Rich Co<sub>40</sub>Fe<sub>25</sub>Cr<sub>20</sub>Ni<sub>15</sub> High-Entropy Alloy via Al Alloying

Simultaneously enhancing strength and ductility of HCP titanium via multi-modal grain induced extra dislocation hardening

Plasticity Improvement in a Co-Rich Co40Fe25Cr20Ni15 High-Entropy Alloy via Al Alloying

Nanoprecipitate and stacking fault-induced high strength and ductility in a multiscale heterostructured high-entropy alloy

Heterogeneous Structure Design to Strengthen Carbon-Containing CoCrFeNi High Entropy Alloy

Additively manufactured heterogeneous precipitation-strengthened high-entropy alloys with high strength and ductility

Developing harmonic structure in CoCrFeMnNi high entropy alloy to enhance mechanical properties via powder metallurgy approach

Simultaneously enhancing strength–ductility synergy in refractory high entropy alloys by a heterogeneous structure design

The predicted rate-dependent deformation behaviour and multistage strain hardening in a model heterostructured body-centered cubic high entropy alloy

Strength-ductility synergy of an additively manufactured metastable high-entropy alloy achieved by transformation-induced plasticity strengthening

Cyclic plasticity of an interstitial high-entropy alloy: experiments, crystal plasticity modeling, and simulations

Yield strength-ductility trade-off breakthrough in Co-free Fe40Mn10Cr25Ni25 high-entropy alloys with partial recrystallization