Abstract:The enhancement of charge separation and utilization efficiency in both the bulk phase and interface of semiconductor photocatalysts, as well as the expansion of light absorption range, are crucial research topics in the field of photocatalysis. To address this issue, twinned Cd0.5Zn0.5S (T-CZS) homojunctions consisting of wurtzite Cd0.5Zn0.5S (WZ-CZS) and zinc blende Cd0.5Zn0.5S (ZB-CZS) were synthesized via a hydrothermal method to facilitate the bulk-phase charge separation. Meanwhile, Cu2-xSe with localized surface plasmon resonance effect (LSPR) generated by Cu vacancies was also obtained through a hydrothermal process. Due to their opposite electronegativity, a solvent evaporation strategy was employed to combine Cu2-xSe and T-CZS by intermolecular electrostatic. After optimization, the photocatalytic hydrogen (H2) evolution rate of 5 wt% Cu2-xSe/T-CZS reached an impressive value of 60 mmol∙h-1∙g-1, which was 4.6 and 66.6 times higher than that of pure Cu2-xSe and T-CZS, respectively. Furthermore, this composites demonstrated a remarkable rate of 0.46 mmol∙h-1∙g-1 under near-infrared (NIR) wavelength (>800 nm). The enhanced performance observed in Cu2-xSe/T-CZS can be attributed to its unique and efficient double S-scheme charge transfer mechanism which effectively suppresses rapid recombination of electron-hole pairs both within the bulk phase and at the surface interfaces; this conclusion is supported by Density Functional Theory (DFT) calculations as well as electron paramagnetic resonance spectroscopy analysis. Moreover, incorporation of Cu2-xSe enables effective utilization ultraviolet visible-near infrared (UV-Vis-NIR) light by the composites while facilitating injection "hot electrons" into T-CZS for promoting photocatalytic reactions. This study provides a potential strategy for achieving efficient solar energy conversion through synergistic integration of non-stoichiometric plasmonic materials with photocatalysts with twinned-twinned structures.

CdSe With Mixed Zincblende and Wurtzite Phases Grown on Lattice-Matched InAs Substrates Using Molecular Beam Epitaxy

Strategy for Performance Enhancement of Cd1-XZnXTe/CdS Core/shell Quantum Dot Sensitized Solar Cells Through Band Adjustment

Optimization of growth conditions of type-II Zn(Cd)Te/ZnCdSe submonolayer quantum dot superlattices for intermediate band solar cells

Double S-scheme Cu2-xSe/twinned-Cd0.5Zn0.5S homo-heterojunctions with surface plasmon effects for efficient photocatalytic H2 evolution

Fabrication and Optimization of CdSe Solar Cells for Possible Top Cell of Silicon‐Based Tandem Devices

High-efficient Sb 2 Se 3 solar cell using Zn x Cd 1- x S n-type layer

Hydrazine Hydrate‐Induced Surface Modification of CdS Electron Transport Layer Enables 10.30%‐efficient Sb2(S,Se)3 Planar Solar Cells

Structural, Electronic and Defect Properties of Cu<sub>2</sub>ZnSn(S,Se)<sub>4</sub> Alloys

CdS(In)/CZTSSe bandgap alignment engineering for performance enhancement of solar cells without ZnO layer

Compositional Dependence of Structural and Electronic Properties of Cu2ZnSn(S,Se)4alloys for Thin Film Solar Cells

CZTSSe solar cell with an efficiency of 10.19% based on absorbers with homogeneous composition and structure using a novel two-step annealing process

Structural, Electronic and Defect Properties of Cu 2 ZnSn(S,Se) 4 Alloys

Doping Behavior of Zn in CdS and Its Effect on the Power Conversion Efficiency of the Cu2ZnSn(S, Se)4 Solar Cell

Preparation of Wide Bandgap CuGaSe2 Absorbers and Solar Cells by Sputtering a Selenium-Rich Ceramic Target and Annealing in a Selenium-Free Atmosphere

Preparation of wide bandgap CuGaSe 2 absorbers and solar cells by sputtering a selenium-rich ceramic target and annealing in a selenium-free atmosphere

Dual-Absorber Solar Cell Design and Simulation Based on Sb2Se3 and CZTGSe for High-Efficiency Solar Cells

Growth of Zn doped Cu(In, Ga)Se 2 thin films by RF sputtering for solar cell applications

Optimized grain growth for efficient solution-processed Bi-doped Cu2ZnSn(S,Se)4 thin film solar cells via spin-coated layers adjustment and two-step selenization

Standing 1D Chains Enable Efficient Wide‐Bandgap Selenium Solar Cells

Beyond 11% Efficient Cu2ZnSn(Se,S)(4) Thin Film Solar Cells by Cadmium Alloying

Cu2ZnSn(S, Se)4 solar cell with slight band tailing states achieves 11.83% efficiency by selenizing sputtered Cu–Zn–Sn–S precursor