Abstract:Abstract Additive manufacturing (AM) is a developing manufacturing technology, which provides excellent attributes compared to other manufacturing techniques. However, one of the critical challenges is the presence of defects that hinder the mechanical properties of the parts, particularly the fatigue life. Experimental understanding of fatigue is a cumbersome process. Therefore, numerical prediction based on specified conditions (such as porosity and applied load) can be an alternative to experimental analysis at the design stage of AM parts. In this study, elastic–plastic finite element analysis (FEA) is performed to obtain the stress distribution around pores, and their resultant effect on fatigue life for L-PBF (laser powder bed fusion) produced AlSi10Mg alloy samples. The stress field is calculated for both single and multiple pore models, where stress concentration is evaluated as a function of the pore’s location and its size. It is found that both pore location and size affect the stress field; however, location effects dominate over pore size. For the same remote applied stress level, the stress concentration around the pore increases with an increase in pore size, and the local maximum stress occurs near the pores that are closest to the surface. The current study also evaluates the relative effect of porosity fraction, average pore size, and location. It is found that the magnitude and sensitivity of stress concentration are hierarchically controlled by porosity location, pore size, and porosity density. A multi-scale finite element (FE) model is proposed based on inherent porosity data measured using Computed Tomography (CT) to predict overall fatigue life. The fatigue cycles are calculated using the rainflow counting algorithm in FE Safe using the stress–strain data obtained from the proposed FEA model. Using the proposed model, it is possible to generate S–N curves for any loading condition for a given porosity condition (porosity density and average pore size). The S–N curve results obtained from the FE model are compared to the experimental observations. The predicted fatigue life shows approximately 5% error with experimental results at high stress loading conditions. However, the proposed model overpredicts the fatigue life at low stress loading by almost 30%.

Fatigue evaluation on the effect of impact pits with various impact conditions by a CDM‐based approach

Fatigue tests and damage model development on Al-Si-Mg aluminum alloys with low-velocity impact pit

A Model for Ultra Low Cycle Fatigue Damage Prediction of Structural Steel

Continuum Damage Mechanics Based Fatigue Life Prediction and Fatigue Property Analysis of Pitting Corrosion Steel Bars

Fatigue tests and a damage mechanics-based fatigue model on a cast Al-Si-Mg aluminum alloy with scratches

An Insight into the Creep-Fatigue Damage Localization in Welded Joints Based on Crystal Plasticity Finite Element Method

Quantitative Study of High-Frequency Fatigue Hole-Edge Stresses in Nickel-Based Single-Crystal Superalloy

Analysis of thermal-mechanical coupling strength and fatigue life of cylinder head

A new combined impact fatigue damage model and its application of influencing factors analysis on impact fatigue of TC18 titanium alloy

The potency of defects on fatigue of additively manufactured metals

Fatigue crack growth and life prediction of 7075-T62 aluminium-alloy thin-sheets with low-velocity impact damage under block spectrum loading

The experimental and numerical study of AA6061-T6 aluminum alloy under repeated impacts

A Modified Normal Strain Ratio Fatigue Life Model Based on the Hybrid Approach of Critical Plane and Crystallographic Slip Theory

An Evaluation on High Cycle Fatigue Fracture Characteristics of 2024-T351 Al Alloy with Different Surface Defects

Fatigue crack propagation within Al-Cu-Mg single crystals based on crystal plasticity and XFEM combined with cohesive zone model

Analysing the effect of defects on stress concentration and fatigue life of L-PBF AlSi10Mg alloy using finite element modelling

Fatigue Damage Behavior and Mechanism Research of 2198 Aluminum–Lithium Alloy Sheet with Error Holes

Multiaxial Fatigue Lifetime Estimation Based on New Equivalent Strain Energy Damage Model under Variable Amplitude Loading

A CDM model for remaining fatigue-lifetime prediction of ductile metals

New ultra-low cycle fatigue model for metal alloys

Influence of Multi-Holes on Fatigue Behaviors of Cast Magnesium Alloys Based on In-Situ Scanning Electron Microscope Technology