Abstract:Crack behavior of aluminum alloy 2A12-T4 is investigated experimentally and numerically using cruciform specimens subjected to in-plane biaxial loadings applied in horizontal (x axis) and vertical (y axis) directions. Different cruciform configuration plans, with variant sizes of slots in loading arms and different transitional fillet radius between adjacent arms, are analyzed by means of FEM to confirm a final specimen geometry with relative uniform stress distribution in its central area. The tests for fatigue crack growth behavior under cyclic biaxial sinusoidal loadings with phase differences of 0 degrees or 60 degrees between two orthogonal fatigue loads are conducted by using a biaxial fatigue test system. The biaxial load ratio, P-max(x)/P-max(y), varies from -0.5 to 1.0. Initial central cracks are inclining in angles of 0 degrees, 45 degrees and 60 degrees to x-axis. Crack growth path and lives are obtained. It is observed that the crack growth behavior under biaxial loading differs from that with only uniaxial loading. A widely accepted fatigue crack growth model, which combines Paris equation, maximum tangential stress (MTS) criterion and an equivalent stress intensity factor (SIF) proposed by Tanaka, is used for mixed mode-I/II crack subjected biaxial loading. The combined model is evaluated by the SIFs analysis based on analytical and numerical solution. The mixed mode SIFs are calculated based on finite element analysis with mesh updating. The simulated crack growth path and growth lives correlate well with the experiments in most cases. Both the experiments and the simulations demonstrate that the tensile load parallel to crack path behaves as the retarder to the crack growth, and the compressive load parallel to crack path behaves as the promoter to the crack growth. It is found that equivalent SIF used in the model overestimates the effect of mode II SIF on the fatigue crack growth rate by Paris equation. It is questionable to use the combined model for the cases with asynchronous biaxial loadings or those leading to crack surface contact.

Fatigue crack propagation within Al-Cu-Mg single crystals based on crystal plasticity and XFEM combined with cohesive zone model

Fatigue Crack Propagation Across Grain Boundary of Al-Cu-Mg Bicrystal Based on Crystal Plasticity XFEM and Cohesive Zone Model

Fatigue Crack Propagation of AA2024 Alloy under Texture Control Using Crystal Plasticity Coupled with Accelerated Cyclic Cohesive Zone Model

A Crystallographic Model for the Orientation Dependence of Low Cyclic Fatigue Property of a Nickel-Base Single Crystal Superalloy

Thermo-Mechanical Fatigue Constitutive Model for Nickel-Based Single Crystal Superalloys

Low-cycle Fatigue Behavior and Life Prediction of TA15 Titanium Alloy by Crystal Plasticity-Based Modelling

Fatigue Crack Behaviors under Asynchronous Biaxial Loading

Anisotropy in fatigue crack propagation behavior of Al-Cu-Li alloy thick plate

Creep-fatigue Behavior of Nickel-Based Single Crystal Superalloy with Different Orientations: Experimental Characterization and Multi-Scale Simulation

Understanding the Small Creep-Fatigue Crack Growth Mechanism of Polycrystalline Alloy Based on Crystal Plasticity and Extended Finite Element Method

Goss Texture Intensity Effect on Fatigue Crack Propagation Resistance in an Al-Cu-Mg Alloy

Microstructure sensitivity of the low cycle fatigue crack initiation mechanisms for the Al 0.3 CoCrFeNi high entropy alloy: in-situ SEM study and crystal plasticity simulation

Study on the crack nucleation mechanism of Ti-2Al-2.5Zr alloy in low cycle fatigue: Quasi in-situ experiments and crystal plasticity simulation

Study of Fatigue Crack Growth Behaviour of Al-Mg and Al-Mg-Sc-Zr Alloys

Texture Effect on Fatigue Crack Propagation Behavior in Annealed Sheets of an Al-Cu-Mg Alloy

Influence of Grain Structure and Precipitates on Fatigue Crack Propagation Behaviors of Al-xCu-1.2Li-X Alloys

Influence of grain structure and precipitates on fatigue crack propagation behaviors of Al- x Cu-1.2Li-X alloys

Fatigue crack propagation anisotropy of an Al–Zn–Mg–Cu super-thick plate

Effect of Grain Orientation Distribution on the Mechanical Properties of Al-7.02Mg-1.78Zn Alloys

Effects of grain structures on fatigue crack propagation behavior of an Al-Cu-Li alloy

Microscopic fatigue crack propagation model for polycrystalline alloys