Abstract:Obtaining intergranular and transgranular fractures through grain boundary engineering has been considered an efficient technique that improves the effective fracture toughness of polycrystalline aggregates. In this paper, the idealized hexagonal microstructure, random microstructures, and microstructures of grains with large aspect ratios are analyzed through a semi-analytical approach and the cohesive finite element method. The results indicate that when the aspect ratio of grains is not too large, the crack paths consisting of intergranular and transgranular fractures are approximately Mode I fracture morphologies among these microstructures. As the ratio of toughness between grain boundaries and grains varies, the effective fracture toughness of the microstructure can be increased more than the grain boundary fracture toughness but cannot exceed the inner grain fracture toughness. In contrast, the microstructure of grains with a large aspect ratio leads to deflected crack paths that are unexpectedly obtained, which implies that the approximate Mode-I intergranular fracture along transverse direction is almost impossible. The results demonstrate that the projected energy dissipation rate along the direction perpendicular to the loading axis can be significantly improved beyond the inner grain fracture toughness by enlarging the aspect ratio of the grains. Nevertheless, the mixed-mode effective fracture toughness is still limited to the grain fracture toughness. Corresponding experiments are also carried out to qualitatively verify the numerical results. The underlying mechanism for this deflection of fracture path is due to the strong anisotropy of fracture toughness. The higher the grain aspect ratio, the greater the anisotropy of the macroscopic effective fracture toughness. The energy favored fracture path is determined by the largest ratio between the driving force and the toughness of fracture over all directions. Therefore, cracks cannot propagate in the direction of the maximum fracture toughness when the aspect ratio of the grain is sufficiently large. The fracture diagrams that vary with the aspect ratio of grain and the ratio of fracture toughness between the grain and grain boundary are provided. The results can provide valuable guidance for designing microstructures and improving fracture toughness in materials.

Crystal cracking of grain-gradient aluminum by a combined CPFEM-CZM method

Constitutive modeling of mechanical behaviors in gradient nanostructured alloys with hierarchical dual-phased microstructures

Micromechanical Simulation of Fracture Behavior of Nanostructured Metals with Bimodal Grain Size Distribution

Diffusive crack-grain interplay in freestanding nanocrystalline silver thin film

Fracture Model of Al–Cu Alloys with Gradient Crystals Based on Crystal Plasticity

Investigation of Grain Boundary Content on Crack Propagation Behavior of Nanocrystalline Al by Molecular Dynamics Simulation

Crystal Plasticity Finite Element Simulation Study on Thread Rolling Pure Aluminum

A study relating to the enhancement of transgranular fracture by iron in AlZnMg alloys

Crystal Plasticity Finite Element Simulation of Grain Evolution Behavior in Aluminum Alloy Rolling

Study on the crack nucleation mechanism of Ti-2Al-2.5Zr alloy in low cycle fatigue: Quasi in-situ experiments and crystal plasticity simulation

Fatigue crack propagation within Al-Cu-Mg single crystals based on crystal plasticity and XFEM combined with cohesive zone model

Influence of Grain Orientation and Grain Boundary Features on Local Stress State of Cu-8Al-11Mn Alloy Investigated Using Crystal Plasticity Finite Element Method

Microstructure sensitivity of the low cycle fatigue crack initiation mechanisms for the Al 0.3 CoCrFeNi high entropy alloy: in-situ SEM study and crystal plasticity simulation

In-situ EBSD Study of the Active Slip Systems and Lattice Rotation Behavior of Surface Grains in Aluminum Alloy During Tensile Deformation

Microstructure design and mechanical properties of grain-gradient graphene/aluminum composites

Selective growth of recrystallizing grains into well-characterized deformed aluminum at hardness indentation

Crystal plasticity modeling of grain boundary softening and fatigue in U75V pearlite steel under low strain conditions: A study of cyclic rolling contact fatigue

Molecular Dynamics Simulations of Pre-Crack Effects on Deformation and Failure Mechanisms for Pure Aluminum

Could Effective Fracture Toughness of Polycrystalline Aggregates Exceed Inner Grain Fracture Toughness by Adjusting Toughness of Grain Boundary?

Grain-orientation induced stress formation in AA2024 monocrystal and bicrystal using Crystal Plasticity Finite Element Method

Investigation of Grain Boundary and Orientation Effects in Polycrystalline Metals by a Dislocation-Based Crystal Plasticity Model