Abstract:Hierarchical ZSM‐5 zeolite materials with different SiO2/Al2O3 molar ratios in the range of 60–300 were synthesized using soft templating and microemulsion methods to generate zeolite materials with narrow mesopore size distributions. The resulting materials were characterized by X‐ray flourescence (XRF), Fourier transform infra‐red (FTIR) spectroscopy, X‐ray diffraction (XRD), scanning electron microscopy (SEM), ammonia temperature programmed desorption (NH3‐TPD), thermo‐gravimetric analysis (TGA), Brunauer‐Emmett‐Teller (BET) surface area measurements, and products from the catalytic tests were analyzed by gas chromatography (GC). The XRF analysis determined that the Si/Al ratios for the synthesized ZSM‐5 were close to the batch ratios. The XRD and FTIR results revealed that the synthesized samples had crystalline ZSM‐5 zeolite structures. The small angle observed from the XRD patterns confirmed the presence of mesopores in the structure of the prepared materials. The SEM results showed that the ZSM‐5 synthesized materials had different morphologies and particle sizes, as well as worm‐like holes indicating that some macropores with average pore sizes ranging between 68 and 85 nm were successfully generated in these materials. NH3‐TPD results showed that the total acidity of the prepared materials decreased with an increase in the Si/Al (SA) ratio following this trend: SA = 71 > 177 > 345. This may be due to the decrease in the aluminum content, which is largely responsible for the formation of acidic sites in zeolites. The acid strength was found to increase with a decrease in the Si/Al ratio, highlighted by the peak shifts to higher temperatures. From the BET results, the SA = 71 was observed to have the highest SSA of 618 m2/g given by its micropore area of 103 m2/g and an external surface area of 515 m2/g. The high external surface area present in the material was due to the development of mesopores with narrow pore size distribution of approximately 6 nm indicating the success of the microemulsion method for the generation of hierarchical zeolites with well controlled pore sizes. The hierarchical ZSM‐5 catalysts were tested for the cracking of various hydrocarbon chain lengths. Low conversions, less than 10%, were obtained in the cracking of hexane; however, when cracking longer chain C12 hydrocarbons, the conversion increased remarkably to 100%. The catalyst with SA = 71 had the highest selectivity towards ethylene and propylene olefins due to its higher acidity in comparison with the other prepared catalysts. Improved activity, selectivity towards ethylene and propylene greater than 60%, and enhanced catalyst stability were demonstrated when using a hierarchical ZSM‐5 compared to the commercial catalyst in the cracking of dodecane. High selectivity towards light olefins was obtained for the cracking of waste tire‐derived oil. The results suggest that these hierarchical materials are suited to the cracking of long chain hydrocarbons and are promising materials for the valorization of waste tire‐derived oils.

Synthesis and Catalytic Evaluation of Mesoporous Molecular Sieve Supported Hydrocracking Catalysts

Nanometer β Zeolite Made from Mesoporous Zeolite and Its Hydrocracking Performance

Hydrocracking of Heavy Oil Using Zeolites Y/Al-SBA-15 Composites As Catalyst Supports

Preparation of Y-type molecular sieve based on bentonite and study of its performance in hydrocatalytic cracking of shale oil

Hydrocracking of Bio-Alkanes over Pt/Al-MCM-41 Mesoporous Molecular Sieves for Bio-Jet Fuel Production

Ordered Mesoporous Materials with Improved Stability and Catalytic Activity

Synthesis of Nanoporous Flower-like Y-SAPO-11 Composite Molecular Sieves for Hydrocracking of n -Hexadecane

Effect of Zeolite-Y Modification on Crude-Oil Direct Hydrocracking

Mesoporous Materials from Zeolite Seeds As Supports for Nickel Tungsten Sulfide Active Phases

Synthesis of CuO–ZnO–Al2O3 @ SAPO-34 Core@shell Structured Catalyst by Intermediate Layer Method

Synthesis of mesoporous high-silica zeolite Y and their catalytic cracking performance

Modification of SBA-15 mesoporous silica as an active heterogeneous catalyst for the hydroisomerization and hydrocracking of n-heptane

Crucial Role of Silica-Alumina Binder Mixtures for Hydrocarbon Cracking with ZSM-5 Additives

Preparation of novel hierarchical catalysts by simultaneous generation of β-zeolite and mesoporous silica for catalytic cracking

Effective hierarchical ZSM‐5 catalysts for the cracking of naphtha and waste tire‐derived oil to light olefins

Synergetic Regulation of the Microstructure and Acidity of HZSM-5/MCM-41 for Efficient Catalytic Cracking of n-Decane

Synthesis of hollow mesoporous aluminosilicate spheres and its catalytic cracking properties

Mesoporous Aluminosilicate Catalysts for the Selective Isomerization of n-Hexane: The Roles of Surface Acidity and Platinum Metal.

Catalytic Cracking of n-Dodecane to Chemicals: Effect of Variable-Morphological ZSM-5 Zeolites Synthesized Using Various Silica Sources

DEHYDROGENATION AND HYDRODESULFURIZATION ACTIVITY OF HETEROATOM-CONTAINING HMS MESOPOROUS MOLECULAR SIEVE CATALYSTS

Synthesis and optimization of Ni/Mo-impregnated kaolin-based ZSM-5 as a catalytic hydrocracking catalyst for heavy petroleum distillates