Abstract:Hierarchical ZSM‐5 zeolite materials with different SiO2/Al2O3 molar ratios in the range of 60–300 were synthesized using soft templating and microemulsion methods to generate zeolite materials with narrow mesopore size distributions. The resulting materials were characterized by X‐ray flourescence (XRF), Fourier transform infra‐red (FTIR) spectroscopy, X‐ray diffraction (XRD), scanning electron microscopy (SEM), ammonia temperature programmed desorption (NH3‐TPD), thermo‐gravimetric analysis (TGA), Brunauer‐Emmett‐Teller (BET) surface area measurements, and products from the catalytic tests were analyzed by gas chromatography (GC). The XRF analysis determined that the Si/Al ratios for the synthesized ZSM‐5 were close to the batch ratios. The XRD and FTIR results revealed that the synthesized samples had crystalline ZSM‐5 zeolite structures. The small angle observed from the XRD patterns confirmed the presence of mesopores in the structure of the prepared materials. The SEM results showed that the ZSM‐5 synthesized materials had different morphologies and particle sizes, as well as worm‐like holes indicating that some macropores with average pore sizes ranging between 68 and 85 nm were successfully generated in these materials. NH3‐TPD results showed that the total acidity of the prepared materials decreased with an increase in the Si/Al (SA) ratio following this trend: SA = 71 > 177 > 345. This may be due to the decrease in the aluminum content, which is largely responsible for the formation of acidic sites in zeolites. The acid strength was found to increase with a decrease in the Si/Al ratio, highlighted by the peak shifts to higher temperatures. From the BET results, the SA = 71 was observed to have the highest SSA of 618 m2/g given by its micropore area of 103 m2/g and an external surface area of 515 m2/g. The high external surface area present in the material was due to the development of mesopores with narrow pore size distribution of approximately 6 nm indicating the success of the microemulsion method for the generation of hierarchical zeolites with well controlled pore sizes. The hierarchical ZSM‐5 catalysts were tested for the cracking of various hydrocarbon chain lengths. Low conversions, less than 10%, were obtained in the cracking of hexane; however, when cracking longer chain C12 hydrocarbons, the conversion increased remarkably to 100%. The catalyst with SA = 71 had the highest selectivity towards ethylene and propylene olefins due to its higher acidity in comparison with the other prepared catalysts. Improved activity, selectivity towards ethylene and propylene greater than 60%, and enhanced catalyst stability were demonstrated when using a hierarchical ZSM‐5 compared to the commercial catalyst in the cracking of dodecane. High selectivity towards light olefins was obtained for the cracking of waste tire‐derived oil. The results suggest that these hierarchical materials are suited to the cracking of long chain hydrocarbons and are promising materials for the valorization of waste tire‐derived oils.

Hydrocracking of Heavy Oil Using Zeolites Y/Al-SBA-15 Composites As Catalyst Supports

Core-Shell Zeolite Y@Gamma-Al2o3 Nanorod Composites: Optimized Fluid Catalytic Cracking Catalyst Assembly for Processing Heavy Oil

Effect of Zeolite-Y Modification on Crude-Oil Direct Hydrocracking

Synthesis of Nanoporous Flower-like Y-SAPO-11 Composite Molecular Sieves for Hydrocracking of n -Hexadecane

Effects of post treatment of HZSM-5 zeolites on catalytic cracking of butene

Synthesis of mesoporous high-silica zeolite Y and their catalytic cracking performance

Synthesis and Catalytic Evaluation of Mesoporous Molecular Sieve Supported Hydrocracking Catalysts

Hydrocracking of Bio-Alkanes over Pt/Al-MCM-41 Mesoporous Molecular Sieves for Bio-Jet Fuel Production

Preparation of hierarchical β and Y zeolite-containing mesoporous silica–aluminas and their properties for catalytic cracking of n-dodecane

Bifunctional catalyst with high efficiency for converting hydrocarbons: The enhanced diffusion between micro and meso-pores

ZSM–5@KIT–6 encapsulated composite molecular sieves for the catalytic cracking of waste cooking oil model compound to produce light olefins

Synthesis of Small Crystal Size Y Zeolite Catalysts with High Hydrocracking Performance on n -Hexadecane

A defect-based strategy for the preparation of mesoporous zeolite Y for high-performance catalytic cracking

Dual Effects of Zinc Species on Active Sites in Bifunctional Composite Catalysts Zr/H[Zn]ZSM-5 for Alkylation of Benzene with Syngas

Zeolite domination in coordination between metal and acid sites on an industrial catalyst for tetralin hydrocracking

Synthesis and Assessment of Y-Zeolite Catalyst for Direct Olefin Production from Heavy Feedstock: An Effect of Feed Composition

Synergetic Regulation of the Microstructure and Acidity of HZSM-5/MCM-41 for Efficient Catalytic Cracking of n-Decane

EFFECT OF USY ZEOLITE ON SURFACE STRUCTURE AND ACTIVITY OF HYDROCRACKING CATALYST

Crucial Role of Silica-Alumina Binder Mixtures for Hydrocarbon Cracking with ZSM-5 Additives

Effective hierarchical ZSM‐5 catalysts for the cracking of naphtha and waste tire‐derived oil to light olefins

Sulfonated Mesoporous Y Zeolite with Nickel to Catalyze Hydrocracking of Microalgae Biodiesel into Jet Fuel Range Hydrocarbons