Abstract:A series of hydrocracking catalysts based on mesoporous molecular sieves of MCM-41 and SBA-15 with different silica to alumina ratios was prepared. Nickel and molybdenum were used as active metals to impregnate the extrudates prepared by using molecular sieves. The catalysts were characterized for physical and chemical properties and evaluated for the hydrocraking of desulfurised vacuum gas oil. The conversion of DS-VGO was lower as compared to that of the catalyst based on USY zeolite. However, the gas yield was lower in case of mesoporous materials based catalysts. Introduction Zeolites are widely used as catalysts in petroleum refining and for the production of petrochemicals and fine chemicals. Recently, the breakthrough discovery of the M41S family mesoporous materials [1,2] exemplified by the MCM-41 bearing hexagonal-close-packed channels. Despite the excellent structural properties, the hydrothermal stability of MCM-41 and MCM-41-like mesoporous materials was reported as lower than their counter part zeolites. Recently, a new kind of mesoporous silica, SBA-15, has been synthesized with poly (alkylene oxide) triblock copolymers such as poly (ethylene oxide)-poly (propylene oxide)poly (ethylene oxide) (PEO-PPO-PEO) [3]. Beside its uniform and large pore size channels (4.6-30 nm), SBA-15 possesses thick walls (3.1-6.4 nm). Therefore, it has much higher hydrothermal stability than MCM-41 [3]. Owing to their extremely large surface area (generally exceeding 1000 mg) and ultra large pore size these mesoporous materials have attracted great practical and academic interest as acid-catalyzed reactions of large molecules such as hydroprocessing of residual oil [4-5]. In this study, the preparation of MCM-41 and SBA-15 with Si/Al 10, 20 and hydrocracking catalysts based on these mesoporous materials along with USY zeolite are presented. Commercial USY zeolite used in this study also has mesopores in it. Nickel and molybdenum are impregnated as active metals. Mesoporous materials and hydrocracking catalysts prepared were characterized by XRD, surface are, pore volume, pore-size distribution, particle size measurement, and acidity measurement by FTIR and ammonia TPD. The side crushing strength of the extrudates with alumina binder was also measured by crushing strength tester. The catalysts were evaluated for hydrocracking of desulfurized vacuum gas oil (DS-VGO). The hydrocracking activity was measured by GC-SIMDIST method and sulfur and nitrogen contents of the product were measured by elemental analyzer.

Synthesis of Nanoporous Flower-like Y-SAPO-11 Composite Molecular Sieves for Hydrocracking of n -Hexadecane

Hydrocracking of Heavy Oil Using Zeolites Y/Al-SBA-15 Composites As Catalyst Supports

Design and Preparation of Efficient Hydroisomerization Catalysts by the Formation of Stable Sapo-11 Molecular Sieve Nanosheets with 10-20 Nm Thickness and Partially Blocked Acidic Sites

Synthesis of nano-sized small-crystal and hierarchical SAPO-11 molecular sieves and superior catalytic performance of their NiWS-supported catalysts in hydroisomerization of n-hexadecane

Preparation and n-hexadecane hydroisomerization properties of SAPO-11-based composite molecular sieve

Novel synthesis strategy of SAPO-11 molecular sieve with superior performance for hydroisomerization of long-chain n-alkanes: Supergravity-cyclone assisted hydrothermal crystallization method

Direct Synthesis of Hierarchical SAPO-11 Molecular Sieve with Enhanced Hydroisomerization Performance

Synthesis of Small Crystal Size Y Zeolite Catalysts with High Hydrocracking Performance on n -Hexadecane

Synthesis of Nickel In Situ Modified SAPO-11 Molecular Sieves and Hydroisomerization Performance of Their NiWS Supported Catalysts

Synthesis and Catalytic Evaluation of Mesoporous Molecular Sieve Supported Hydrocracking Catalysts

Deep Hydroisomerization of n-Hexadecane over NiWS/SAPO-11 Catalyst: Size Effect of the Support and Revelation of the Reaction Network

Core-Shell Zeolite Y@Gamma-Al2o3 Nanorod Composites: Optimized Fluid Catalytic Cracking Catalyst Assembly for Processing Heavy Oil

SAPO-11 molecular sieves synthesized in alcohol-water concentrated gel system with improved acidity, mesoporous volume and hydroisomerization performance

Preparation of nano ZSM-5 with hydrophobic surfaces and application to catalytic cracking of hydrocarbon fuels

Small-crystal and hierarchical SAPO-11 molecular sieve synthesized via three-stage crystallization method and hydroisomerization performance of corresponding NiWS supported catalyst

Synergetic Regulation of the Microstructure and Acidity of HZSM-5/MCM-41 for Efficient Catalytic Cracking of <i>n</i>-Decane

Synergetic Regulation of the Microstructure and Acidity of HZSM-5/MCM-41 for Efficient Catalytic Cracking of n-Decane

Synthesis of Ni/SAPO-11-X Zeolites with Graded Secondary Pore Structure and Its Catalytic Performance for Hydrodeoxygenation-Isomerization of FAME for Green Diesel Production

Supported CoW Bifunctional Catalyst with High Activity and Selectivity for Hydrocracking Alkane

Synthesis and Performance of Pillared HZSM-5 Nanosheet Zeolites for N-Decane Catalytic Cracking to Produce Light Olefins

Effects of Channel Structure and Acidity of Molecular Sieves in Hydroisomerization of N-Octane over Bi-Functional Catalysts