Abstract:It has been shown experimentally that the Hall-Petch relation of nanocrystalline (NC) metal will be broken down when the average grain size (d) is below a critical value, but the mechanism behind this remains to be quantitatively analyzed. In order to capture the subtle evolution of grain boundaries (GBs), we recently developed a novel algorithm by using moving least-squares (MLS) interpolant. Moreover, the phase field model is used to build NC copper with more natural and physical GBs for molecular dynamics (MD) tensile simulation. The results show that the variation of stress at GBs (σGB) and at grain interiors (σGI) in the elastic stage are in good agreement with previous study. The σGB exhibits periodic vibration, while σGI shows a linear behavior. From the stress distribution, we find that the increased σGB in one cycle can make the σGI increase. The microplasticity of GBs occurs when σGB increases to a peak value, which attenuates the stress concentration and then leads to the decrease of the σGB. Therefore, the σGI can be affected by the frequency of vibrated σGB. The fast Fourier transform (FFT) results show that the dominant frequency for the model with d of 13.8 nm is larger than that for other models, which causes a larger Young's modulus in the model. The GBs and GIs supplement each other during deformation: GBs providing an extra stress to GIs, GIs supplying the space for microplasticity of GBs. Besides, the fraction of deformed GBs and rotated GBs in the model are also large. GB activities are the results of overall microplasticity before σGB = σGI and deformation during the plastic stage. The rotated GBs results in the emission of many Shockley partial dislocation (partials) from GBs since they create larger paths for dislocation movement. Thus, many twinning boundaries (TBs) are generated in the model with d of 13.8 nm by partials gliding on the successive plane of adjacent stacking faults (SFs) structures, which plays an important role in work hardening of NC Cu.

Displacement fields around Guinier–Preston 1 zones in Al–Cu alloys: investigations using MD and ADF-STEM image simulations

Three-dimensional characterization of Guinier–Preston zones in an Al–Cu alloy using depth-sectioning technique

Experimental examination of strain field within GP zone in an Al–Zn–Mg–Cu alloy

The copper content of Guinier–Preston (GP1) zones in Al–1.84 at.% Cu alloy

Guinier-Preston zones observed by high-angle annular detector dark-field scanning transmission electron microscopy

In Situ Atomistic Observation of Grain Boundary Migration Subjected to Defect Interaction

An atomistic investigation of the interaction of dislocations with Guinier-Preston zones in Al-Cu alloys

Direct imaging of Guinier-Preston zones by high-angle annular detector dark-field scanning transmission electron microscopy

Optimal Arrangements and Local Anisotropy of {100} Guinier–Preston (GP) Zones by Parametric Dislocation Dynamics (PDD) Simulations

Revisiting the precipitation mechanisms of Guinier-Preston zones, η′, and η precipitates in Al-Zn-Mg alloys

Small-angle scattering from GP zones in Al-Cu alloy

Strengthening of Al-Cu alloys by Guinier-Preston zones: predictions from atomistic simulations

Atomistic modeling of nucleation kinetics of Guinier–Preston zones in Al–Cu alloys: Two formation scenarios and prediction of the time-temperature-transformation diagram

Morphological evolution of GP zones and nanometer-sized precipitates in the AA2050 aluminium alloy

High resolution electron microscopy on the layered structures of GP zones in an Al-1.7at%Cu alloy

Unexpected Capture of Guinier-Preston Zone and Γ″ Phase in As-Cast Mg-Gd-Y-Zn-Ni-Mn Alloy: Atomic-scale Insights

High-resolution transmission electron microscopy and tomographic atom probe studies of the hardening precipitation in an Al–Cu–Mg alloy

On the Guinier-Preston zones in selective laser melted AlSi10Mg alloy

Quantifying the influence of grain boundary activities on Hall-Petch relation in nanocrystalline Cu by using phase field and atomistic simulations

Morphology and mechanical properties of nanocrystalline Cu/Ag alloy

EFFECT OF SYMMETRICAL TILT GRAIN BOUNDARIES ON DISPLACEMENT CASCADES IN FE-CR-AL ALLOYS BASED ON ATOMIC SIMULATIONS