Abstract:The surface preparation is a prerequisite for ensuring the required properties of a diamond film formed by gas-phase deposition. The influence of the temperature and concentration of the CuSO 4 etchant on the structural and phase compositions of the surface of hard-alloy materials is considered in this work, and the structural and phase compositions of a continuous polycrystalline diamond film at its growth stages is also considered. The adhesion of the diamond films to the surface of hard-alloy materials is determined qualitatively. It is established that the treatment of the hard-alloy surface in the CuSO 4 solution at t = 23°C leads to the inhomogeneous removal of a cobalt binder with chipping WC grains and the formation of the porous structure in the surface layer of the WC–6% Co alloy. The treatment by the CuSO 4 etchant at t = –2°C provides the homogeneous etching of the Co binder over the boundaries of WC grains and the formation of a chemically homogeneous surface. The orientation growth and adhesion of the diamond film depend on the elemental composition of the WC–Co alloy surface after treatment by the CuSO 4 solution. If the treatment was performed at t sln = 23°C, then the removal of copper from the defect surface WC layer is complicated during the synthesis, which provides the multidirectional growth of diamond crystals in the film along two directions, 〈111〉 and 〈110〉, which causes critical biaxial compressive stresses (2.5 GPa) and leads to low film adhesion to the hard alloy surface. If the treatment is performed at t sln = –2°C, then the orientational growth of diamond crystals in the film occurs in one preferential crystallographic direction 〈111〉, which lowers the biaxial compressive stresses (1.7 GPa) and increases the adhesive bond of the film to the hard alloy surface. The structure imperfection calculated from the ratio of the lines of integrated intensities I 1333 / I 1580 using the Raman spectroscopy method decreases with an increase in concentration at negative temperatures and increases at positive temperatures of the CuSO 4 solution during surface preparation.

Glancing angle intermediate layer deposition approach for CVD diamond coating of high-speed steel substrates

Diamond-like Carbon Film on 20 CrNiMo Steel Prepared by Hollow-Cathode Glow Discharge

High adhesion diamond films deposited on stainless steel by using nanocomposite films with mosaic interface as an interlayer

Deposition of an adherent diamond film on stainless steel using Cr/CrAlN as an interlayer

Understanding of the adhesive strength enhancement mechanisms of bilayer diamond film at nanoscale

Interlayers Applied to CVD Diamond Deposition on Steel Substrate: A Review

A Strategy for Alleviating Micro Arcing during HiPIMS Deposition of DLC Coatings

Group growth of polycrystalline diamond coating by MPCVD technique on a hard alloy tool with a thin blade

Ion Beam Assisted Deposition of Diamond-Like Carbon Onto Steel Materials: Preparation and Advantages

Unveiling the formation of Mo2C coating on diamond particles along with anisotropic etching by Mo powder

Deposition of diamond film on steel substrate by precoating an intermediate layer

Growth Features of Diamond Films on the Tungsten Carbide Surface with a Copper Sublayer

Engineered CVD Diamond Coatings for Machining and Tribological Applications

Effect of Molybdenum Concentration and Deposition Temperature on the Structure and Tribological Properties of the Diamond-like Carbon Films

Improvement in the universality of high-performance CVD diamond coatings on different WC-Co substrates by introducing multilayered diamond/β-SiC composite

Interface study of CVD diamond films grown on molybdenum

TiMoTa multi-component transition layer: Plasma in-situ diagnosis, mechanical properties and effect on diamond adhesion

Achieving precise graphenization of diamond coatings below the interfacial thermal stress threshold

Direct coating adherent diamond films on Fe-based alloy substrate: the roles of Al, Cr in enhancing interfacial adhesion and promoting diamond growth

Microwave plasma CVD of diamond films on high concentration alloys: Microstructure, hardness and wear properties

A competitive-adsorption chemical vapor deposition method: Diamond coated on WC-Co substrate without acid-alkali pretreatment by adding graphene oxide particles