Abstract:In this paper, diamond-like carbon (DLC)/graphite-like carbon (GLC) composite coatings were deposited by using high-power impulse magnetron sputtering (HIPIMS). The effect of HIPIMS mean power and pulse width on the surface morphology, carbon atomic bonding structure, mechanical properties, compressive stress, and tribological performance of the DLC/GLC coatings were characterized using laser scanning confocal microscopy, Raman spectroscopy, nano-indentation, compressive stress tester, and ball-on-plate tribometer, respectively. The results show that the mean power and pulse width have significant influence on the formation of GLC microparticles and sp3 C-C content. Both increasing mean power and/or decreasing pulse width could increase the target current density, causing the enhancement of the ionization rate of carbon and subsequently improving the sp3 fraction of the coatings. Increasing pulse width would extend the arc discharge time, resulting to an increase in the amount and size of the GLC microparticles. The mechanical properties and compressive stress dominantly depend on the sp3 C-C fraction of the coatings. But the coating tribological performance shows a significant relationship with the embedded GLC microparticles that can help to decrease the friction coefficient. However, the relatively soft GLC microparticles would decrease the coating wear resistance. It is believed that the tribological performance of the DLC/GLC coatings can be controlled via adjusting the HIPIMS parameters.

A Strategy for Alleviating Micro Arcing during HiPIMS Deposition of DLC Coatings

Two-Layer Nanocomposite TiC-Based Coatings Produced by a Combination of Pulsed Cathodic Arc Evaporation and Vacuum Electro-Spark Alloying

High-ion-energy and low-temperature deposition of diamond-like carbon (DLC) coatings with pulsed kV bias

Deposition of nano-diamond-like carbon films by an atmospheric pressure plasma gun and diagnostic by optical emission spectrum on the process

Excellent Adhered Thick Diamond-Like Carbon Coatings by Optimizing Hetero-Interfaces with Sequential Highly Energetic Cr and C Ion Treatment

Surface Roughness Influence on Tribological Behavior of HiPIMS DLC Coatings

Plackett-Burman experimental design for pulsed-DC-plasma deposition of DLC coatings

Adhesion Enhancement on a Duplex DLC HiPIMS Positive Pulse Coating Performed by Active Screen Plasma Nitriding Pretreatment on 316L Stainless Steel Substrate

Influences of target power and pulse width on the growth of diamond-like/graphite-like carbon coatings deposited by high power impulse magnetron sputtering

A Study of Hard Diamond-Like Carbon Films in Mid-Frequency Dual-Magnetron Sputtering

Study on Influence of Target Powers on Properties of Diamond-Like Carbon Films Deposited by Mid-Frequency Magnetron Sputtering System

Microstructure and Surface Properties of Chromium-Doped Diamond-Like Carbon Thin Films Fabricated by High Power Pulsed Magnetron Sputtering

Study on the Effect of Ar-containing Work Gas on the Microstructure and Tribological Behavior of Nanocrystalline Diamond Coatings

Advanced Tribological Characterization of DLC Coatings Produced by Ne-HiPIMS for the Application on the Piston Rings of Internal Combustion Engines

Studies of Diamond-Like Carbon Films Prepared by Ion Beam-Assisted Deposition

Diamond-Like Carbon Coatings on Plasma Nitrided M2 Steel: effect of deposition parameters on adhesion properties

Effect of W-doping on the structure and properties of DLC films prepared by combining physical and chemical vapor deposition

Feasible Power for DLC Deposition on Alumina by RF-biased Inductively Coupled Plasma: Effect of Atmospheric Parameters

Magnetron Sputtering Preparation of Diamond-Like Carbon Film Adhesion Characteristics Research

Improved Interfacial Adhesion Between TiAlN/DLC Multi-Layered Coatings by Controlling the Morphology Via Bias

Microstructure and Tribological Properties of Diamond-Like Carbon and Tialsicn Nanocomposite Coatings