Abstract:A high‐speed solid‐state coating method using mechanical fusion to fabricate an LiFe0.4Mn0.6PO4 olivine enamel‐like layer on lithium cobalt oxide is proposed. The coating contributes to fabricating thin/stable cathode–electrolyte interphase from outside‐in and restraining surface Co3O4 formation from inside‐out, preventing block of Li+ diffusion and over‐consumption of active Li. It is believed that this facile/scalable method can establish a technical criterion for multifarious surface‐modified electrode candidates. The high‐voltage induced undesirable surface passivation bilayer (cathode/electrolyte interface and cation‐densified surface phase) of LiCoO2 inevitably leads to battery degradation. Herein, a continual/uniform enamel‐like olivine layer on LiCoO2 surface is fabricated by employing a high‐speed mechanical fusion method . The enamel‐like layer suppresses interfacial side reactions by tuning EC dehydrogenation, contributing to an ultrathin and stable cathode/electrolyte interface. The strong bonding affinity between LiCoO2 and enamel‐like layer restrains both lattice oxygen loss and associated layered‐to‐spinel structural distortion. Moreover, the thermal stability of highly delithiated LiCoO2 is improved, as both the onset temperatures of layered‐to‐spinel transition and O2 evolution are simultaneously postponed. Stable operation of LiCoO2 at 4.6 V high‐voltage and 55 °C elevated temperature (both >85% capacity retention after 200 cycles) is achieved. This facile and scalable high‐speed solid‐phase coating strategy establishes a technical paradigm to enhance surface/interface stability of high‐energy‐density cathode candidates by constructing an ideal enamel‐like surface layer.

Pushing Lithium Cobalt Oxides to 4.7 V by Lattice‐Matched Interfacial Engineering (Adv. Energy Mater. 23/2022)

Pushing Lithium Cobalt Oxides to 4.7 V by Lattice‐Matched Interfacial Engineering

Scalable Precise Nanofilm Coating and Gradient Al Doping Enable Stable Battery Cycling of LiCoO2 at 4.7 V

Ultrahigh‐voltage LiCoO2 at 4.7 V by Interface Stabilization and Band Structure Modification

Surface engineering of LiCoO2 by a multifunctional nanoshell for stable 4.6V electrochemical performance

Highly stable operation of LiCoO2 at cut-off ≥ 4.6 V enabled by synergistic structural and interfacial manipulation

Ultrathin Dense LiF Coverage Coupled with a Near-Surface Gradient Fluorination Lattice Enables Fast-Charging Long-Life 4.6 V LiCoO2

Structure/Interface Coupling Effect for High‐Voltage LiCoO2 Cathodes

Lattice‐Matched Interfacial Modulation Based on Olivine Enamel‐Like Front‐Face Fabrication for High‐Voltage LiCoO2

Ultrathin dense LiF coverage coupled with a near-surface gradient fluorination lattice enables fast-charging long-life 4.6 V LiCoO<sub>2</sub>

Lithium-Aluminum-Phosphate Coating Enables Stable 4.6 V Cycling Performance of LiCoO2 at Room Temperature and Beyond

Structure/Interface Coupling Effect for High‐Voltage LiCoO2 Cathode

Ultrahigh-Voltage LiCoO 2 at 4.7 V by Interface Stabilization and Band Structure Modification.

Outside‐In Nanostructure Fabricated on LiCoO2 Surface for High‐Voltage Lithium‐Ion Batteries

Structure/Interface Coupling Effect for High‐Voltage LiCoO<sub>2</sub> Cathodes

Improving Stability of High Voltage LiCoO2 by Synergetic Surface Modification Via in Situ Surface Conversion

Electrochemical surface passivation of LiCoO2 particles at ultrahigh voltage and its applications in lithium-based batteries

Stabilizing LiCoO2 at 4.6 V by regulating anti-oxidative solvents

Kinetics Enhancement of High‐Voltage LCO via In‐Situ Formed Cyanide‐Rich Polymer Interfaces

An in Situ Formed Surface Coating Layer Enabling LiCoO2 with Stable 4.6 V High‐Voltage Cycle Performances

Channelization of cathode/electrolyte interphase to enhance the rate-capability of LiCoO2