Abstract:A surface‐to‐bulk modification with Li2TiO3 coating and gradient Ti doping is demonstrated to solve the deterioration of LiCoO2 at high voltage. The synergetic modification enhances Li+ diffusion, facilitates the construction of high‐quality cathode/electrolyte interphase, reduces the phase transition from O3 to H1‐3 and Co3d/O2p band overlap, and restrains layer‐to‐spinel phase distortion, thus improving structural stability at 4.6 V. Elevating the charging cut‐off voltage is an effective strategy to increase the energy density of LiCoO2. However, unstable interfacial structures and unfavorable phase transitions in bulk are inevitably triggered during deep de‐lithiation at high voltage. Herein, an integrated surface‐to‐bulk Ti‐modification strategy is applied to LiCoO2, enabling uniform Li2TiO3 coating on the surface and gradient Ti‐doping toward the structural bulk. The resultant Ti‐modified LiCoO2 (T‐LCO) electrode can be stably cycled up to 4.6 V, providing a high‐rate capability of 137 mAh g−1 at 5C and a long‐life stability with 80.5% capacity retention after 400 cycles at 1C, far outperforming the unmodified LiCoO2 electrode with only 50.7% capacity retention. In situ X‐ray diffraction characterization and density functional theory calculation reveal that the synergistic modification of T‐LCO enhances Li+ diffusion, facilitates the construction of high‐quality cathode/electrolyte interphase, reduces the phase transition from O3 to H1‐3 and Co3d/O2p band overlap, and restrains layer‐to‐spinel phase distortion, thus improving structural stability at 4.6 V. This work presents a "two birds one step" strategy to enhance the cycling stability and achievable capacity of high‐voltage LiCoO2 for developing high energy density lithium‐ion batteries.

Ultrahigh-Voltage LiCoO 2 at 4.7 V by Interface Stabilization and Band Structure Modification.

Ultrahigh‐voltage LiCoO2 at 4.7 V by Interface Stabilization and Band Structure Modification

Scalable Precise Nanofilm Coating and Gradient Al Doping Enable Stable Battery Cycling of LiCoO2 at 4.7 V

Stabilizing 4.6 V LiCoO2 via Surface‐to‐Bulk Titanium Modification

Highly stable operation of LiCoO2 at cut-off ≥ 4.6 V enabled by synergistic structural and interfacial manipulation

Pushing Lithium Cobalt Oxides to 4.7 V by Lattice‐Matched Interfacial Engineering

Improved Stability of Single‐Crystal LiCoO2 Cathodes at 4.8 V through Solvation Structure Regulation

In Situ-Constructed Multifunctional Interface for High-Voltage 4.6 V LiCoO2

Lithium-Aluminum-Phosphate Coating Enables Stable 4.6 V Cycling Performance of LiCoO2 at Room Temperature and Beyond

Enhanced cycle stability of LiCoO2 at high voltage by mixed conductive Li7.5La3Zr1.5Co0.5O12 coating

A multifunctional manipulation to stabilize oxygen redox and phase transition in 4.6 V high-voltage LiCoO2 with sXAS and EPR studies

Stable Cycling of LiCoO2 at 4.55 V Enabled by Combined Mg Doping and Surface Coating of NASICON-type Electrolyte

Bimetallic synergistic modified layer promotes the cyclic stability of LiCoO 2 under 4.6 V high voltage

Reducing Co/O Band Overlap Through Spin State Modulation for Stabilized High Capability of 4.6 V LiCoO2.

Structure/Interface Coupling Effect for High‐Voltage LiCoO2 Cathodes

A Novel Bifunctional Self‐Stabilized Strategy Enabling 4.6 V LiCoO2 with Excellent Long‐Term Cyclability and High‐Rate Capability

Densification of Cathode/Electrolyte Interphase to Enhance Reversibility of LiCoO<sub>2</sub> at 4.65 V

Additive Evolved Stabilized Dual Electrode-Electrolyte Interphases Propelling the High-Voltage Li||LiCoO 2 Batteries up to 4.7V

Improving Stability of High Voltage LiCoO2 by Synergetic Surface Modification Via in Situ Surface Conversion

Superior stable high‐voltage LiCoO2 enabled by modification with a layer of lithiated polyvinylidene fluoride‐derived LiF

Structure/Interface Coupling Effect for High‐Voltage LiCoO<sub>2</sub> Cathodes