Abstract:A new strategy; cation and anion dual gradient, is proposed and successfully constructed at the surface of LiCoO2 to minimize the highly oxidized Co4+ and O− species when charged to high potentials, which not only suppresses the relevant surface side reactions, but also affected the Li+ diffusion kinetics through the induced spinel‐like surface structure, making LiCoO2 exhibit excellent cycling stability and rate capability at the high cutoff voltage of 4.6 V, further validated in the 4.55 V pouch full cell (equivalent to 4.6 V vs Li/Li+).LiCoO2 (LCO) is the most successful cathode material for commercial lithium‐ion batteries. Cycling LCO to high potentials up to 4.5 V or even 4.6 V can significantly elevate the capacity but cause structural degradation due to the serious surface side reaction between the highly oxidized Co4+ and O− species with organic electrolytes. To tackle this concern, a new strategy, constructing cation and anion dual gradients at the surface of LCO (DG‐LCO), is proposed. Specifically, the electrochemically inactive cation and anion are selected to substitute Co3+ and O2− at the surface in a gradated manner, thus minimizing the highly oxidized Co4+ and O− species at high potentials and suppressing the induced surface side reactions. Unexpectedly, this dual gradient design leads to a spinel‐like surface structure coherently with bulk layered structure, which facilitates Li+ diffusion kinetics. Thus, DG‐LCO achieves high capacity and excellent cycling stability at 4.6 V (≈216 mA h g−1 at 0.1 C, a capacity retention of 88.6% after 100 cycles in 1.8 A h pouch full cell at 1 C), as well as improved rate capability (≈140 mA h g−1 at 5 C). These studies provide useful guidelines for future design of cathode materials with long lifespan and high rate capability.

Ultrathin dense LiF coverage coupled with a near-surface gradient fluorination lattice enables fast-charging long-life 4.6 V LiCoO<sub>2</sub>

Ultrathin Dense LiF Coverage Coupled with a Near-Surface Gradient Fluorination Lattice Enables Fast-Charging Long-Life 4.6 V LiCoO2

Mixed Lithium Ion and Electron Conducting LiAlPO 3.93 F 1.07 -Coated LiCoO 2 Cathode with Improved Electrochemical Performance

Ultrathin dense LiF coverage coupled with a near-surface gradient fluorination lattice enables fast-charging long-life 4.6 V LiCoO 2

Superior stable high‐voltage LiCoO2 enabled by modification with a layer of lithiated polyvinylidene fluoride‐derived LiF

Surface Design with Cation and Anion Dual Gradient Stabilizes High‐Voltage LiCoO 2

Operating Highly Stable LiCoO2 Cathodes up to 4.6 V by Using an Effective Integration of Surface Engineering and Electrolyte Solutions Selection

Regulating Electrode/electrolyte Interfacial Chemistry Enables 4.6 V Ultra-Stable Fast Charging of Commercial LiCoO2

Surface Design with Cation and Anion Dual Gradient Stabilizes High‐Voltage LiCoO2

Lithium-Aluminum-Phosphate Coating Enables Stable 4.6 V Cycling Performance of LiCoO2 at Room Temperature and Beyond

Hybrid ion/electron interfacial regulation stabilizes the cobalt/oxygen redox of ultrahigh-voltage lithium cobalt oxide for fast-charging cyclability

Diffusion‐Optimized Long Lifespan 4.6 V LiCoO2: Homogenizing Cycled Bulk‐To‐Surface Li Concentration with Reduced Structure Stress

Densification of Cathode/Electrolyte Interphase to Enhance Reversibility of LiCoO<sub>2</sub> at 4.65 V

Facile Formation of a LiF-Carbon Layer as an Artificial Cathodic Electrolyte Interphase through Encapsulation of a Cathode with Carbon Monofluoride

Surface Design with Cation and Anion Dual Gradient Stabilizes High-Voltage LiCoO<sub>2</sub>

Anticorrosive nanosized LiF thin film coating for achieving long-cycling stability of LiCoO2 at high voltages

Pushing Lithium Cobalt Oxides to 4.7 V by Lattice‐Matched Interfacial Engineering

Sn, S co-doped LiCoO 2 with low lithium ion diffusion energy barrier and high passivation surface for fast charging lithium ion batteries

Scalable Precise Nanofilm Coating and Gradient Al Doping Enable Stable Battery Cycling of LiCoO2 at 4.7 V

Ultrahigh‐voltage LiCoO2 at 4.7 V by Interface Stabilization and Band Structure Modification

Densification of Cathode/Electrolyte Interphase to Enhance Reversibility of LiCoO2 at 4.65 V