Abstract:This paper evaluates popular methods for balancing CR‐VCOs' outputs. It assesses the effectiveness of those methods in terms of mismatch cancellation, PVT robustness, and phase noise. This work proposes a CR‐VCO with inherent ability to generate balanced outputs. It is achieved by implementing single‐ended tank capacitors to shunt the common‐mode voltage to a real ground. Summary In the first part of this paper, we closely examine well‐known methods for balancing the output power level of the pseudo‐differential current‐reuse voltage‐controlled oscillator. We scrutinize their effectiveness in terms of canceling output mismatches, insensitivity to process, voltage, and temperature variations, and their capability of not degrading phase noise performance. Through analyses and simulations, it is shown that contrary to common belief, some techniques are not as effective as previously thought and should be employed only under specific circumstances. The best conventional approach is proven to be the use of a common‐mode shunting capacitor at the inductor's center tap node to create a virtual ground. In the second part, it is demonstrated that the current‐reuse voltage‐controlled oscillator can intrinsically produce balanced outputs without using any additional techniques or extra passive or active components. Using single‐ended tank capacitors instead of differential ones, the common‐mode voltage of the outputs is shunted to the real ground. This technique reintroduces a reference voltage to the tank circuit, forcing the oscillator to achieve equilibrium between positive and negative swings. The proposed current‐reuse oscillator is designed and post‐layout simulated in a 65‐nm CMOS process, covering a frequency range of 4.84–6.38 GHz with an average power consumption of 0.65 mW. It produces balanced outputs with an amplitude error of less than ±0.2% and achieves a phase noise of −126.7 dBc/Hz and FoMT of 201.8 dB at a 3‐MHz offset frequency.

A detailed study of the current‐reuse VCO's operation and a simple circuit technique to generate intrinsic‐balanced outputs

A Low Phase Noise VCO with Placement Reordered Cores and High-Q Bond Wire Array Inductors

A Bridged Contactless Measurement Technique for LC Tank Based Voltage-Controlled Oscillator.

A 1mW 5GHz current reuse CMOS VCO with low phase noise and balanced differential outputs

A Wideband Voltage-Controlled Oscillator with Gain Linearized Varactor Bank

A 12.5-to-15.4ghz, -118.9Dbc/hz PN at 1mhz Offset, and 191.0dbc/hz FoM VCO with Common-Mode Resonance Expansion and Simultaneous Differential 2Nd-Harmonic Output Using a Single Three-Coil Transformer in 65nm CMOS.

A current-reuse Class-C LC-VCO with an adaptive bias scheme

Analysis and design of a new low‐phase noise and Gm‐enhanced class‐C quadrature VCO

An Enhanced Class-F Dual-Core VCO With Common-Mode-Noise Self-Cancellation and Isolation Technique

A 4.4-Ghz 193.2-Db FoM 8-Shaped-inductor Based LC-VCO Using Orthogonal-Coupled Triple-Coil Transformer

An Ultra-Low-Voltage High-Performance VCO in 0.13 μm CMOS

A Low Noise Self-Mixing-VCO Based on Coupled Class-F 2 Oscillators

A Complementary Oscillator Using a Current-Limiting Tail Resistor in 180nm CMOS

A Low Noise Self-Mixing-VCO Based on Coupled Class-F<sub>2</sub> Oscillators

CMOS Voltage-Controlled Oscillator with Complementary and Adaptive Overdrive Voltage Control Structures

A 2.15–6.18 GHz transformer-based dual-mode LC-VCO with current-reuse technology

A Transformer-Based Series-Resonance CMOS VCO

A Uniform Phase Noise QVCO with a Feedback Current Source

A 418 GHz CMOS Fully Integrated LC Balanced Oscillator with Symmetrical Noise Filter Technique and Large Tuning Range

A Swing-Enhanced Current-Reuse Class-C VCO with Dynamic Bias Control Circuits

A 12.3–18.5-Ghz Single-Core Oscillator Using a Dual-Mode Variable Inductor with a Tunable Self-Resonant Frequency Technique