Abstract:Airlift pumps are a versatile category of two-phase flow equipment principally employed for the transportation of liquids. Facilitating interfacial heat and mass transfer between gas and liquid phases, these pumps have the potential to serve as an efficient heat and mass exchanger in various industrial applications. Nonetheless, this capability of airlift pumps has remained relatively unexplored in the existing literature; therefore, present study aims at experimentally characterizing sensible heat and evaporative mass transfer performance of airlift pumps. In this study, a series of experiments were conducted using an airlift pump with a riser pipe diameter of 25.4 mm and a submergence ratio of 70 %; air and water were utilized as the gas and liquid phases, respectively. The experiments were performed under both isothermal and non-isothermal two-phase flow conditions; the gas temperature ranged from 22 °C to 110 °C, and the inlet air flow rate varied from 0.43 to 5.12 kg/hr . Instantaneous void fraction data were collected using a capacitance sensor and underwent evaluation through both Probability Density Function (PDF) and Power Spectral Density (PSD) statistical analysis. These analyses were coupled with flow visualization results obtained from high-speed imaging to analyze the two-phase flow hydrodynamics quantitatively and qualitatively. The study identified three flow patterns (slug flow, intermittent flow, and churn flow), and detected notable transformations in elongated bubbles and the formation of small bubble clusters and aerated regions. It was also found that churn flow exhibits the highest delivered liquid flow rate, while slug flow demonstrates the best lifting efficiency under both operational conditions. Also, the pump displayed notably higher lifting efficiencies under isothermal operation compared to non-isothermal one. Moreover, both sensible heat and evaporative mass transfer revealed improved performance with increasing inlet air flow rate, reaching maximum coefficients in the churn flow regime. Gas temperature in the present range found to have negligible effect on the two-phase interfacial structures, flow pattern transition, and delivered liquid flow rate, but a considerable positive impact on void fraction, lifting efficiency, and heat and mass transfer coefficients under non-isothermal operation.

Mass transfer characteristics of water-driven partially submerged self-rotating disk-based mass exchanger

Hydrodynamics And Mass Transfer Performance In A Modified Rotating Disc Contactor

Hydrodynamics and Mass Transfer Performance of a Modified Rotating Disc Contactor (MRDC)

Study on Hydrodynamics and Mass Transfer Characteristic of a New Gas-liquid Reactor

Experimental Study on Gas–liquid Dispersion and Mass Transfer in Shear-Thinning System with Coaxial Mixer

Advances in design, scale and operability of the Rotating Liquid Sheet (RLS) contactor: Pressure drop, flood-point and mass transfer – comparison to random packing

Flow Boiling in Dimpled Plate Heat Exchangers with Different Geometric Parameters: Analysis of Asymmetric Channels

Research, Development and Industrial Application of New Rotating Disc Contactor

Power-efficient mass transfer of a novel pulsating multi-packed bed liquid - liquid extractor

Passive, active, and interactive drag-reduction technique to reduce friction and enhance the mixing intensity in rotating disk apparatus

Experimental evaluation of airlift pumps' thermal and mass transfer capabilities

Gas-Liquid Mass Transfer Characteristics in a Rotating-Drum Bioreactor

Physical Modelling and Numerical Simulation of Velocity Fields in Rotating Disc Contactor Via Cfd Simulation and Ldv Measurement

Hydrodynamics and Mass Transfer in A Countercurrent Multistage Microextraction System

Characterization and Scaling of Forced Convective Swirl in Sinusoidal Wavy-Plate-Fin Cores of Compact Heat Exchangers

Liquid-liquid Flow and Mass Transfer Characteristics in a Miniaturized Annular Centrifugal Device

Experimental investigation of two-phase flow in Chevron-type compact plate heat exchangers: A Study on pressure drops and flow regimes visualization

Mass transfer performance in a coalescence–dispersion pulsed sieve plate extraction column

Determination of the Liquid Hold-Up Volume and the Interface Radius of an Annular Centrifugal Contactor Using the Liquid-Fast-Separation Method

A Dynamic Forward Mixing Model for Evaluating the Mass Transfer Performances of an Extraction Column

Improved Mass-Transfer Model for Distillation in a Pilot-Scale Concentric Ring Rotating Bed as a Rotating Packed Bed