Abstract:The numerical prediction of strain distribution in multi-gauge, aluminum alloy sheet tailor welded blanks (TWBs) is undertaken using the explicit dynamic finite element code LS-DYNA. The limiting dome height test (LDH) is modeled considering three gauge combinations: 2mm to 1mm, 2mm to 1.6mm and 1.6mm to 1mm and various weld line orientations relative to loading direction. Two welding techniques are considered: non-vacuum electron beam (NVEB) and dual beam Nd:YAG. Formability data is presented in terms of limiting dome height to failure measurements, as well as measured limit strains and indicates that the Nd:YAG process is superior to the NVEB process considered. In general, the model agrees with measured strain distributions relatively well, particularly in cases when weld failure dominates as in the NVEB welds. The model is overly conservative, however, for the higher performance Nd:YAG-welded blanks which generally fail in the thinner parent metal away from the fusion zone. The shell element-based model fails to capture through-thickness constraint effects near the weld and consequently localizes in the row of elements immediately adjacent to the weld line. On a entrepris la prédiction numérique de la distribution de contrainte d'échantillons soudés sur mesure de feuilles d'alliage d'aluminium de différentes épaisseurs, en utilisant le code explicite dynamique d'élément fini LS-DYNA. On a modélisé l'épreuve de la hauteur limitante du dôme en considérant trois combinaisons d'épaisseur, soit 2 mm à 1mm, 2 mm à 1.6 mm et 1.6 mm à 1 mm. On a considéré deux techniques de soudage: le faisceau électronique sans vide (NVEB) et le faisceau double Nd:YAG. En général, le modèle s'accorde relativement bien avec la distribution de déformation mesurée, particulièrement dans les cas où le lâchage de la soudure domine, tels que pour les soudures au NVEB. Cependant, le modèle est excessivement conservateur dans le cas des meilleures performances des échantillons soudés au Nd:YAG, lesquels lâchent généralement dans le métal-parent le plus mince, à l'écart de celui de fusion. Le modèle basé sur l'élément de l'enveloppe ne réussit pas à capturer les effets de contrainte à travers l'épaisseur près de la soudure et, conséquemment, les localise dans la rangée d'éléments immédiatement adjacents à la ligne de soudure‥

Bending Limit Prediction of an Aluminum Thin Sheet

Prediction of failure in bending of an aluminium sheet alloy

Influence of ductile damage on the bending behaviour of aluminium alloy thin sheets

Prediction of Minimum Bending Ratio of Aluminum Sheets From Tensile Material Properties

Ductile Failure Predictions for the Three-Point Bending Test of a Complex Geometry Made From Aluminum Alloy

Ductile fracture prediction in aluminium alloy 5A06 sheet forming based on GTN damage model

Numerical analysis of ductile fracture in stretch bending of AA6061-T6 aluminum alloy sheet using GTN damage model

Experimental and numerical investigation of failure during bending of AA6061 aluminum alloy sheet using the modified Mohr-Coulomb fracture criterion

Forming Limit Prediction of Anisotropic Aluminum Magnesium Alloy Sheet AA5052-H32 Using Micromechanical Damage Model

Prediction of limit strains in hot forming of aluminium alloy sheets

Characterization and prediction of fracture in 6000- and 7000-series aluminum alloy sheet under various stress states

A Study to Predict Failure in Biaxially Stretched Sheets of Aluminum Alloy 2024-T3

Experimental and numerical investigations into the ductile fracture during the forming of flat-rolled 5083-O aluminum alloy sheet

Prediction of Strain Distribution in Aluminum Tailor Welded Blanks for Different Welding Techniques

Modeling of the Ductile Fracture During the Sheet Forming of Aluminum Alloy Considering Non-Associated Constitutive Characteristic

Predicting Sheet Forming Limit of Aluminum Alloys for Cold and Warm Forming by Developing a Ductile Failure Criterion

Uncertainties on the mechanical behaviour of bronze sheets: influence on the failure in bending

Characterizing the fracture forming limit curve from shear to uniaxial tension in ultrathin sheet metals using specimens with cutouts

Numerical prediction and experimental validation of forming limit curves of laminated half-hard aluminum sheets

Mechanism-Based Numerical Approach to Ductile Fracture in an 2024–T3 Aluminium Alloy

Prediction of Fracture Behavior of 6061 Aluminum Alloy Based on GTN Model