Abstract:A physically based material model for metals, with elastic–plastic and damage/failure orthotropy is proposed in this paper. The model is defined within the frameworks of irreversible thermodynamics and configurational continuum mechanics and integrated in the isoclinic configuration. The use of the multiplicative decomposition of deformation gradient makes the model applicable to arbitrary plastic and damage deformations. To account for the physical mechanisms of failure, the concept of thermally activated damage initially proposed by Klepaczko (1990) was adopted as the basis for the new damage evolution model. This makes the proposed damage/failure model compatible with the Mechanical Threshold Strength (MTS) model (Follansbee and Kocks, 1988; Chen and Gray, 1996; Goto et al., 2000; Gray et al., 1999; Chen et al., 1998) which was used to control evolution of flow stress during plastic deformation. In addition the constitutive model is coupled with a shock equation of state which allows for modelling of shock wave propagation in the material. The new model was implemented in DYNA3D and our in-house non-linear transient SPH code, MCM (Meshless Continuum Mechanics).Parameters for the new constitutive model for AA7010 (a polycrystalline aluminium alloy, whose orthotropy is a consequence of grain morphology), were derived on the basis of the tensile tests and Taylor anvil tests. The tensile tests were performed for the range of temperatures between 223.15K and 413.15K, and strain rates between 6.4×10-4s-1 and 6.4×101s-1.The new model was validated in two stages. The first stage comprised a series of single element tests design to separately validate elasticity, plasticity and damage related parts of the model. The second stage comprised a series of numerical simulations of Taylor anvil and plate impact tests for AA7010 and comparison of the numerical results with the experimental data. The numerical results illustrate the ability of the new model to predict experimentally observed behaviour.

Forming Limit Prediction of Anisotropic Aluminum Magnesium Alloy Sheet AA5052-H32 Using Micromechanical Damage Model

Numerical Simulation and Defect Prediction of Forming Process for Aluminum Alloy Sheets Considering the Effect of Both Anisotropy and Lode Parameter

Modeling the anisotropic plasticity and damage of AA7075 alloy in hot forming

Forming Limit Prediction Using an Integrated Model for 7075 Aluminum Alloy Sheets at an Elevated Temperature

Anisotropic mechanical behavior prediction of aluminum alloy sheet based on an anisotropic GTN model: Modeling, simulation and experimental investigation

DUCTILE DAMAGE ANALYSIS FOR FRACTURE IN SHEET METAL FORMING BASED ON GTN MESOSCOPIC DAMAGE MODEL

Modeling Anisotropic Ductile Fracture of AA7075-T6 Sheet for Sheet Metal Forming Considering Anisotropic Stress State

Anisotropic Damage and Failure Analysis of Magnesium Alloy Sheet Thermal Stamping

Forming Limit Stress Diagram Prediction of Aluminum Alloy 5052 Based on GTN Model Parameters Determined by in Situ Tensile Test

Ductile damage prediction of AA 5754 sheet during cold forming condition

Forming Limit Stress Diagram Prediction of Pure Titanium Sheet Based on GTN Model

A Novel Continuum Damage Constitutive Model for Predicting the Formability of AA7075 Alloy at Elevated Temperatures

Forming Limit Analysis of Mg-2Zn-1.2Al-0.2Ca-0.2RE Alloy Sheet Using Ductile Fracture Models

A Thermal Forming Limit Prediction Method Considering Material Damage for 22mnb5 Sheet

Modelling of dynamic behaviour of orthotropic metals including damage and failure

Modeling of Anisotropic and Asymmetric Behaviour of Magnesium Alloys at Elevated Temperature Coupled with Ductile Damage

Applying the Damage Constitutive Model for Predicting Thermal Deformation of AA7075 Aluminum Sheet

On the Thermal Forming Limit Diagram (TFLD) with GTN Mesoscopic Damage Model for AA7075 Aluminum Alloy: Numerical and Experimental Investigation

A New Damage Constitutive Model for Thermal Deformation of Aa6111 Sheet

The GTN damage model based on Hill’48 anisotropic yield criterion and its application in sheet metal forming

A Physical-Based Plane Stress Constitutive Model for High Strength AA7075 under Hot Forming Conditions